Model:SH-U11F

If you need RS232, RS485 and similar - especially if you want long term reliability/stability, protection from over-voltage, and flexibility, DSD Tech is the way to go. Can’t recommend them enough At this point I’ve purchased probably 2 or 3 dozen UART/TTL USB adapters from other brands/sellers in my lifetime. I used to think “they’re all the same- cheap, but they work” - but I realized over time that eventually ended up in the trash for one of several reasons- voltage not supported, baud rate not supported, or (most common) unexpectedly stopped functioning With most of the other brands, you have to guess what voltage is supported- if you need anything other than 3.3v, it’s a dice roll. Ditto with baud rate. Need to support more than 1Mbps? Very few sellers even know the max rate of the chip, let alone disclose it to buyers The DSD products all have clear and complete documentation so you know exactly what you’re getting- they’ll tell you “this model only supports X and Y voltage”, or “this model has a max of Z baudrate”, so you know which variant to get Most (or all) of the DSD products have isolated circuitry so they don’t fry your USB port (or themselves) when you inevitably connect to the wrong pins You get exactly what the listing says. And they seem to make just about everything. My favorite is the UART TTL adapter that has support via jumpers for 1.8v, 3.3v and 5v and some less common voltages in between I will never buy a no-name brand again- these may use generic chips underneath, but DTD is not a generic brand The prices are very good- maybe a little more than sone competitors- but it’s worth paying a few extra dollars when you know it will do everything you need into the foreseeable future and won’t die either

This devices works well and is easy to set up. Just be aware you can set it up for 4 wire 422 but not 4 wire 485.

I have it connected to laptop running windows 10. Recognized and installed drivers. Was able to access and send and receive data. Seem to be well built. Leds show power and data (tx/rx).

This is a perfect solution for building new controllers for older hardware. the 485 is a rare beast (in my experience) but this allowed me to easily build a controller to run from the Latest o/s on to the oldest hardware. Easy to work with, well made. was able to build and deploy the test configuration in under 20 minutes. The full working model took a couple of weeks, as I wanted it to do so much! but none of it was difficult. The good documentation from the manufacturer was most pleasing!

This is my second unit with the same issue. I am using a MDO34 oscilloscope and can see my 485 buses drop from 4.4 V to 400 mV whenever I connect this 485 converter. I am using another brand and it works fine. Fortunately, my Rs485 chips can handle the issue and recover. Can't say the same for DSD TECH. I guess I will have to look elsewhere to find a USB converter.

This product does not work and I can't return it. Nice.

On initially receiving the unit the output on both serial and USB was corrupted as though baudrate clock not quite set as needed. Seller immediately replaced the device without any quibbles. New part worked fine. Device provides required grounding and possibility to set termination resistance, great in such a device at this price. Great quality in construction as well. Have now tried it in 2-wire 485 and 4-wire 422/485 and found all OK. For the driver on Win10, don't make my mistake - I initially forgot to run install as Administrator and device was not detected. Run install on extracted exe by right click and select "Run as Administrator ..." and all should be good.

Utilisé dans le cadre de petite prestation, aucun défaut en plusieurs mois.

Empfehlenswert. Sehr schnelle Lieferung. Das Gerät sieht schon mal sehr gut aus und funktioniert auf Anhieb (erstmal an einem Windows-Rechner; USB IDs 0403 6001 = FTDI FT232RNL, kein Treiber-Problem). Transparentes Gehäuse und Platine (ein paar Flussmittelreste, OK) sehen sehr gut und sauber produziert aus. In die Klemmen passen auch größere Durchmesser und/oder Aderendhülsen bis 2.7mm. Leider ist an dem Gehäuse keine Befestigungsmöglichkeit, es muß also irgendwie ge- oder umklemmt werden (H 23.7mm, T48.4mm, L59.2mm; die Nut an der L-Seite ist 1 Zoll breit ca. 3mm tief). Flacher Boden (mit Logo-Einprägung, auf der Bodenseite?!) könnte man auch mit wieder lösbaren Klebepads kleben. Zur Not geht Kabelbinder einmal rum, am USB-Stecker vorbei und durch die Nut hinten/oben und zurück durch die Montageplatte, hält bombig. Habe hier nur kurze Distanzen, ob das Gerät längere Distanzen schafft kann ich nicht sagen.

Lo utilizo para conexiones con HMI (es el tercero que compro, para diferentes proyectos) y el funcionamiento es perfecto.