交付 Hong Kong

获得最佳体验获取应用程序

下载应用程序

我们从

阿联酋
英国
印度
美国
日本
KOREA

客户服务

关于我们

客户支持

Square D by Schneider Electric FSG2J21CP 30-50 PSI Pumptrol Water Pressure Switch

Square D by Schneider Electric FSG2J21CP 30-50 PSI Pumptrol Water Pressure Switch

Q: install instructions for pump water pressure switch

Asuming you are replacing an existing pressure switch, it's a piece of cake. But first I must ask it you are sure the problem is with the switch. I would suggest yo spend a little time doing a few checks. Turn off the power to the switch/pump at the breaker. Remove the plastic cover and look for the contacts. Check the contacts for marks of arcing and carbon build up. Push the overcenter arm to open the contacts and clean the contacts with an emory board/nail file type. When you see clean metal on the contact mating surfaces trip the OC bar back to close the contacts. Energize the circuit and see if the pump runs. If it does not find a volt meter somewhere and measure the voltage across L1 and L2 contacts (from the service panel) then repeat on Load1 and Load 2 (the wires going to the pump). Basicly you are checking the voltage from the service panel and then to the pump. If there is no power on the line side of the switch, there is a problem between the panel and the switch. If there is voltage on the wires heading to the pump the pressure switch is doing its job and the pump wiring or pump are at fault.. If theres voltage in but not out of the switch then replace the switch. Again shut off the power at the service panel. Drain the water system to releive any pressure in the system. Take a picture of the wiring to be sure the new unit is installed identically. Label and remove the wires from their respective terminals. Remove the the cable connector from the sides of the unit to be reused in the new unit. Unscrew the unit from the water system being sure not to stress the connection point on the system. Use a back-up wrench. Pipe dope the new unit's threads an screw it in. Do not over tighten it. Install the cable connects, connect the wires and install the cover. Restore power to the system and see if it works.

Q: Wire connections -- Line Vs. Load. Working with 240v. My unit does not cut off at all and builds excessive pressure causing leeks. Wires are black & w

Turn the circuit breaker off then double check your wiring. You should have 4 wires, a white & a black which is line in, and another set of white and black wires which is line out or load. If it looks okay check your settings., the cut-in should be set at about 30 lbs and the cut out should be about 60 lbs. If all that is okay you may have a defective control. Make sure you turn the circuit breaker on after you finish checking the above. If you can't tell which is line-in you may need a voltage meter to check it. Good luck.

Q: Does this switch has a low pressure cutoff?

I'm not sure what you mean by "low pressure cutoff". However this switch is designed to maintain pressure from your well pump between 30 and 50 psi. If the pressure in the system drops below 30 psi, it kicks the pump on, once it hits 50 psi it kicks the pump off.

Q: my pumptrol square D model number is 9013fsg 2 30/50 psi is it the same as a fsg2j221cp 30/50 can i use it?

Honest answer: I don't know. Having admitted that, I will add for your own decision making: (1) Did Square D just change their model number as a product update? i.e., (2) Are the liquid plumbing fittings the same? (3) Do both models have the same number of hot, neutral, and ground electrical connections? (4) Are the electrical breaker/contact points the same size? (5) Do you have an on/off switch upstream of the Square D to control your system? (6) Is the system fuse-protected upstream from your switch? If the answers to #2-6 are all "yes", it may be worth a try. But if in doubt, do not endanger yourself or anyone else! And feel free to get a second opinion.

4.4/5

产品编号: 405892734

安全交易

细节

Brand
Schneider
Style
Submersible
Power Source
Corded
Global Trade Identification Number
Manufacturer
square
UPC
880828451327

经常一起购买

Telemecanique Sensors FSG2J21CP 30-50 PSI Pumptrol Water Pressure Switch, Grey Cover

MEASUREMAN 0-100 PSI/kPa Water Pressure Gauge, Glycerin Filled,psi Gauge,for Home Water Pressure Test, 2-1/2’’ Dial, 304 Stainless Steel Case, 1/4’’ NPT Lower Mount

Red Brass Pipe Fitting, Nipple, Schedule 40 Seamless, 1/4" NPT Male X 3" Length

描述

规格

Manufacturer	square
Item model number	FSG2J21CP
Product Dimensions	7.06 x 9.55 x 7.11 cm; 372 g
ASIN	B000BQOXV0

有问题吗？看看别人问了什么

install instructions for pump water pressure switch

Wire connections -- Line Vs. Load. Working with 240v. My unit does not cut off at all and builds excessive pressure causing leeks. Wires are black & w

Does this switch has a low pressure cutoff?

my pumptrol square D model number is 9013fsg 2 30/50 psi is it the same as a fsg2j221cp 30/50 can i use it?

常见问题

TrustPilot

TrustScore 4.5 | 7,300多个评论

苏雷什· K.

质量和快速送货让我印象深刻。会再次来这里购物。

4天前

Farhan Q.

交货时间非常好，包装也很安全。

2 个月前

查看所有TrustPiLot评论

全球购物，通过 Desertcart 享受优惠

物有所值

各种产品的价格具有竞争力

全球购物

为 100 多个国家的数百万购物者提供服务

增强保护

深受全球购物者喜爱的值得信赖的支付方式

客户保证

深受全球购物者喜爱的值得信赖的支付方式。

沙漠车应用程序

随时随地随时随地购物。

TrustPilot

TrustScore 4.5 | 7,300多个评论

阿里·H.

发货快，包装精良。Leatherman 工具手感非常高档和坚固。

1天前

拉维·S。

我很喜欢这里提供的多种产品。一定会再次光顾。

2 个月前

查看所有TrustPiLot评论