3D Printer Adhesive Glue by Layerneer, Bed Weld Original, Strong Grip Reduces Warping for ABS, PLA, and PETG Filament on Heated Build Plates, 4 oz.

forget about gluesticks, this has zero mess and total hold. a bit expensive but truly worth it.

Excelente pegamento para el Material

somehow for slightly larger print out around 100x100.. it still can hold it to the bed well.. however, for really large print such as about 200x200, for the prusa printer that we have, ABS still does not hold well on the corner for 200x200

As an avid 3D printing enthusiast, I've tried numerous adhesion solutions over the years, but none have matched the performance of Bed Weld Original, which is now my go-to solution for stopping warping etc. Pros: Strong Grip: This adhesive provides a robust bond between the print bed and the filament, significantly reducing the chances of warping or detachment during printing. Versatility: Compatible with a wide range of filaments, including ABS, PLA, ASA, and PETG, making it a one-stop solution for various printing needs. Easy Application: The bottle is easy to apply, and a little goes a long way, ensuring long-term use without frequent reapplications. Cons: Initial Odour: Upon first application, there is a slight odour, but it dissipates quickly and doesn't affect the print quality. Final Thoughts: If you're looking to improve print adhesion and reduce warping issues, Bed Weld Original is a must-have addition to your 3D printing toolkit. Its strong grip and compatibility with various filaments make it an invaluable asset for both beginners and seasoned professionals.

I've previously been using glue sticks or hairspray for adhesion when printing on glass build plates. While both options work, they are messier, don't always provide consistent adhesion, and can leave an unwanted finish on the bottom of prints (requiring cleaning and/or sanding). The LAYERNEER bed weld is a fantastic product! Here's what I like about it: - The sponge applicator prevents too much product from coming out and makes it very easy to apply the product only where needed. - After applying and allowing the product to dry (dries by the time the bed is heated), the dried product is clear and leaves a smooth (nearly invisible) layer on top of the print bed. - Since the product dries smooth, there's no chance it will cause imperfections on the bottom of the prints (like chunky glue sticks often do). - The product is water soluable, so it's easy to clean off the build plate with hot water. While not required, a small dab of dish soap adds some lubrication and makes washing easier. - The cap securely twists onto the top of the bottle to protect the foam applicator and keep the product from drying out. - One layer is good for 5-10 prints. LAYERNEER states a wet sponge can be used to recharge the bed weld, but I haven't tried that yet. - While washing the build plate will always yield the best results, I'm able to reapply additional layers of bed weld (as needed) a few times before washing the build plate. Some tips for success: - Check out the image LAYERNEER included in the product description for a list of build plates this product works best with. There are a lot of low star reviews here where customers mention they are using build plates that are not on the suggested list (like textured build plates). - Apply the product when the bed is at room temperature. - Shake the bottle for about 5 seconds before applying. There is a ball inside of the bottle (like in a can of spray paint) that helps mix the product. - Press the sponge applicator straight down until it bottoms out on the build plate to allow the product to moisten the sponge applicator. And then lightly brush the sponge applicator acrosss the build plate to distribute the product where needed (wherever the parts will be placed). - Wait for the product to air dry before printing if not using a heated bed. If using a heated bed, the product will be dry by the time the bed reaches the target temperature. - After a print has completed, wait for the bed to cool down to room temperature for easier/cleaner removal. I've been 3D printing (mostly on glass build plates) since 2015. The LAYERNEER bed weld is the best product I've used so far. My only disappointment is that it took me this long to find a product that consistently works well. I'll definitely be purchasing LAYERNEER bed weld again in the future (use Subscribe & Save to save 15%).