EZ-POUR HI-FLO Industrial Can Spout Replacement – Multi-Use For Deluxe Cans and Water Jugs (Pack of 1) - 1, 2, 5 Gallon HI-FLO System with Extension, Flexible Nozzle (40050)

I originally picked up a gas can from a local store, and honestly, it felt like a total waste because of the factory spout. It leaked, dripped, and made transferring fuel into my equipment an absolute mess. I was ready to give up on the can altogether — until I installed the EZ-POUR Gas Can Spout Replacement. What a difference. This HI-FLO system completely changed my opinion of the gas can I purchased. The flow is smooth and controlled, and there’s no more spilling or fuel running down the side of the can. The seal is solid, and everything feels secure and well-designed. It actually works the way a gas can should work. The included extension is an added bonus and makes fueling even easier, especially for equipment with awkward fill angles. The flexible nozzle and flame arrestor give extra confidence and versatility. Never again will I deal with those original “junk” spouts that come standard on so many cans. This replacement is a total game changer and absolutely worth it. Highly recommended!

I finally gave up on the "safety" spouts that come with new gas cans. I can never seem to figure those things out, and they always end up making a mess. The EZ-POUR Replacement is exactly what I needed. It is easy-peasy to install and even easier to use. No clicking, twisting, or frustration—just a straightforward spout that actually pours gas when you want it to. If you're tired of struggling with the over-complicated nozzles that come on gas cans these days, get this. It works perfectly.

Great product! I used to have one of those spring-loaded/safety latch spouts which are terrible. The EZ-POUR is a huge upgrade. No more wrestling with the safety latch and spilling gas in my garage. Very easy to pour gas into my generator now with NO SPILLS using the EZ-POUR. Highly recommend.

They work, and they work pretty well. This is one of many such spout replacements for gas cans. All of them serve the purpose of enabling you to deep-six the cruddy monstrosities that California EPA "experts" have foisted on us under the guise of consumer safety. I have a few points about replacement spouts: One, don't throw away your can's original screw-cap (...with a hole in it), at least, not until you've verified that the replacement screw cap works on your gas-can. I've replaced various crappy California-mandated @&*%##$ NON-pour spouts on a dozen cans, and I've had at least three where the new screw cap DIDN'T FIT THE THREADS ON THE CAN. In this here particular product, they give you not one, but TWO replacement screw-caps, but I'm telling you that for one of my cans, NEITHER OF THEM WORKED...so I was glad I'd kept the old one. Two, it's best if your can is completely empty and dry before you drill the hole for the breather. Most of the time you get at least a few shreds of plastic falling into the can, and it's easier to get them out if the can is dry. Alternatively, you can add a quart or two of water to the can, and rinse the scraps out, repeating as needed...after which you can wait a week for the few drops of water to evaporate, or point a hair dryer through a metal funnel into the open pour-hole and dry it out in five minutes. ...Or you can just say the heck with it, and live with a few drops of water mixed into your gas [guess which method I prefer.] Three, when you drill out the hole for the breather-valve, DON'T DRILL THROUGH A SEAM IN THE CAN! The instructions may or may not tell you to drill the hole in the center of a flat area near the top of the can, but it won't make any difference if you drill it an inch off center, and you won't have a leak when the little breather-valve can't seal on that rough, ugly seam. Four, I've bought three of these, haven't needed the spout extension on any of them. I suppose if you need more than about 8 inches to reach a deeply recessed fill-mouth, a 10-inch extension might be a good idea. Me, I've never had a machine with such a poorly-designed fill-hole. I haven't tried it, but I'll bet you could stretch the opening of the extension to fit over the can's primary spout -- if so, the extension could serve as a spare spout, rather than just another piece of plastic junk that serves no purpose...and which you probably won't be able to find anyway, assuming that you ever do need a really long spout. All of these wondrous words of wisdom are just my humble opinions. And remember, folks: free advice is worth every penny you pay for it.

This is a great product and replaces the leaky crap that comes with gas cans. I recommend it 100%

Save me money by not buying another gas can. This one fits my 5-gal gas can, the extension will work great when filling my Generator up, no more wasted gas. Tried two others and they didn't work, bad as the one came with the can, the safety lock sucked. Life saver. Buy it, you're never regret it.

Works great! So nice to be able to use the gas container with a spout that works without leaking

Purchased this to replace the annoying filler on my standard gas cans to make it easier to pour gas into my van gas tank port. Unfortunately the filler tube diameter is to large to fit the flex-fuel inlet on my van so It doesn't work for that purpose. Otherwise it seems to be good for filling gas tanks with larger filler opennings. It is plastic so it's hard to get overly rated for quality and durability IMHO though.

this is good option for filling diesel without spillage.

Great product. Prevents spilling gas when refilling lawnmower and outboard etc.

Seems to works well my older cans.

Useless for me