Trend Diamond Sharpening Stone Kit, 8 x 3 Inch Double Sided (300/1000 Grit) Bench Stone with Pouch, Cleaning Block & Non-Slip Mat, DWS/CP8/FC

This sharpening stone works great! Being 8"x3" it is the perfect size for sharpening plane blades and chisels. I achieved very sharp edges on my chisels and plane blades and was able to flatten the backs of my blades. I like that it has two sides so I only have one stone to deal with instead of two. I also like that it is monocrystalline instead of polycrystalline; monocrystaline sharpens more efficiently and lasts longer. One side is 300 grit and the other side is 1000 grit. These are marked clearly on each side. Only the 300 grit side has the clearance channels. At the time of this review, the photo advertised here in Amazon is not correct since it shows clearance channels on a 1000 grit stone. These channels are very effective for keeping the lapping fluid evenly distributed on the surface and also clear out some of the metal shavings. The 1000 grit side does not have these channels. I wish it did since it really helps a lot. I find the channels on this Trend stone to be much better than the holes used on DMT stones. While a knife point can still occasionally hang up in these channels, the point will have more tendency to skip over it rather than catching hard like on the edges of the holes on a DMT stone. I sharpened two pocket knives on this stone and only had the knife point hang up once. The channels on the Trend stone also take up less space on the stone, thereby allowing for more diamond cutting surface, unlike the DMT stones where the many big holes leave very little cutting surface left. DMT does have steel plate stones very similar to these Trend stones, but DMT currently does not offer any clearance holes or channels on them. I only used a general purpose household cleaner in a spray bottle as the lubrication. The soapy solution works well as a lubricant and is easy to clean up; it is also very cost effective. Don't' use bathroom cleaners since those can be corrosive if left on metal for too long. Once broken in, my knife and blade edges came out very smooth and sharp. I posted a photo of one of the bad chisels I flattened with this stone. Diamond sharpening stones do require a break in period. The courser the stone, the less time it takes to break in (because there are fewer diamonds to break in on a course stone). When first pulled out of the package, this Trend stone is very rough. I grabbed one of my low quality chisels and started working on it to improve the chisel and break in the stone. The 300 grit side broke-in within about 30 minutes of working this one chisel (the chisel was in really bad shape and would have sharpened quicker if I used an extra course stone). The 1000 grit took about 2.5 to 3 hours of sharpening time with a few different chisels and knives before it broke in. Some people expect the stone to be broke-in right out of the box; however, with a stone that will last for several years, I don't have a problem spending a few hours breaking it in. The pouch it comes with is well made and very handy to have. It also comes with what they call a cleaning block. This item seems to be nothing more than a big pencil eraser. But it is nice they included it. It also comes with a non-slip pad: this is also something you can buy in a home store that is used as liners in drawer bottoms, but again it is very nice they included it. Overall, I am very pleased with the performance of this stone. I highly recommend that if you are looking to get a diamond stone, this one will not disappoint as it is high quality and sharpens wonderfully - far better than sand stones. Updated information: I have also used the DMT diamond stones. I find the trend stones to be far more quality made than DMT. The Trend stone has a more uniform coating of diamonds and the metal block has squared edges instead of slightly rounded edges. The Trend also does not seem to clog as easily as the DMT. The DMT stones also seem to lose diamonds much easier than the Trend. I also believe the Trend is a flatter stone after I attempted to flatten a few plane blades. Therefore, as a side by side comparison, I put Trend stones well above the DMT stones.

I was in the market for a sharpening set to sharpen some router bits and I stumbled across Trend’s sharpening set. When I purchased this set it was 30% off of the already low price of $36. This elder is such a bargain for what you’re paying for. If you purchase everything individually you’re paying almost triple the price. Now just because it’s a bargain doesn’t mean you’re not buying one of the best sharpening tools on the market. The sharpening file is very ergonomic and durable. It’s a breeze to get setup and works wonderfully on your tools that need sharpening. The sharpening stone is dead on flat so you’ll be consistent.

Coarse side sharpens fast. Fine side takes a while to raise a burr. Leaves a good polish on a plane blade.

If you take care of it, it will outlast a DMT plate I used to use mine with the fluid it came with then I used a rust inhibitor with water so I could use it with my bare hands because the fluid that it came with dried my skin out and I could not feel anything with the gloves on. Don’t cross contaminate it will scratch the stone . I use it for knives and woodworking tools and it actually has more character than the DMT plates that I use like I can feel it grabbing the steel the DMT plates are the opposite the steel just slides across the plate they still cut though And the DMT plates that I got seem to be a little bit flatter. I have learned the hard way that this stone is not for chipped edges or edge re-profiling😅. I got a bench grinder for my woodworking tools and an extra course DMT stone for my knives I heard aoma plates are the best diamond plates I cannot back that up with experience though. For flattening, Chisels and plane blades from rusty and pitted or from hardware store it will take you hours for one chisel or plane blade. I would recommend something else like an extra coarse DMT plate. It might even get you there faster if you use a belt sander then go onto the stone. Or just sandpaper on a dead flat rock. I would recommend as a medium stone for a step in edge refinement. I do not use the 300 grit side that much just for flattening it does not do much more than the 1000 for for the sharpening process also, I have had the stone for two years and still works great. when I got it, I paid like 150!

Perfecto para el primer afilado de cuchillas de cepillo o formones. Luego es necesario usar una piedra 6-8mil pero se gana mucho tiempo. Recomiendo usarlo con el líquido de la marca Trend específico para estas piedras de diamante

Affilatura rapida ed efficace. La grana è 300/1000 quindi non aspettatevi una cosa professionale ma per hobbisti va più che bene. L’affilatura risulta buona specialmente per legno dolce.

Cuts quick. Just overall great sharpening tool.

Muy buen producto ,se puede afilar rápidamente sin complicación

Quality kit, but the case is a repurposed facemask case that they have filled with sharpening tools.