74801-01A Bed X-Tender Black

I was looking for a bed extender and AMP absolutely fits the bill. I installed this on a 2014 Tacoma and it will work on many trucks. Very light weight. Be advised, the new bed extenders are now angled at the corners, not squared off. Apparently, the NHTSA - National Highway Transportation Admin, revised their rules to angle these so as not to block brake lights.I found a YouTube video of an install that was useful, but I dint think Amazon will allow posting the link. Therefore, I'll do a walk thru. This kit is very easy to assemble. Be on the lookout for a piece of the cardboard packaging that has a 7" template piece. You will use this to measure 7" from the end of each of the three bars. Put a piece of tape (masking) at the 7" mark. The purpose is so when you assemble the tubes into the ends, you can eye even spacing. I found when I assembled, the tubes inserted right up to the tape and made the extender perfect width for mounting.Another note, there are two frame brackets for the three bars. Look closing at the inside that will last flush with the bars. There are 6 ribs inside. You'll notice 2 are larger, 4 shallower. This is because when you slide the tubs into the ends, the end bars are larger, the inserted tubes smaller. So, if your brackets aren't a tight fit, check to ensure the brackets are place correctly. Thks isn't noted in the directions.The extender comes with the standard mounting bracket. I upgraded and ordered the quick release set. I like having the added locked in feature.Templates - the kit comes with two paper templates, small and large. Small is for small trucks, large for large. That said, I used the small, but once mounted, the extender wasn't level, but tilted. I then used the large template and all worked out great. So, tape each in place and put your assembled extender on the tailgate and you'll be able to quickly see which template is best.Oh, I have two pics of the round tabs that hold in the tailgate latch. For the 2014 Tacoma, you need to remove the larger ones that are on the straps and install the smaller ones; they do come with the kit for the change out.I really like this extender. It took me about an hour and it's a lot easier than it sounds.

Pros- Cost- Used a professional installer to complete the project. (4wheel)- Well built- Every easy to use.Cons-N/AOther thoughts Be sure to purchase the following items to complete the install (if you have a Tonneau Cover and/or shell:AMP Research 74601-01A BedXTender HD Bracket KitAMP Research 74605-01A BedXTender HD Quick Latch Bracket Kit (for use with Tonneau Covers and Shells)AMP's website implies this is optional.. But it is required for 2005 Nissan Frontiers

This product really comes up the the manufacturer’s description, it was super easy for one person to install. I have one negative comment...I lost the packet of attachments to tie the bed extender down...all my fault but I tried ordering the part from Amazon and it’s out of stock and when I called the manufacturer I got a recording and no calls back...I tried three times...COVID-19?I would purchase again!

Love it, good quality and light. I think it is a little overpriced honestly but it works great and is built well enough. About 4 dirt bike trips in and I have no complaints.I will try to save someone time and frustration. If you have a 2001 Toyota Tacoma ext cab two door TRD, you will need the bracket to get this to work without modifying it. The bracket attaches to the very thin metal (seems too thin to me but no probs yet) on the sides of the tail gate area, allowing a place for the bed extender to hook into.

Materials are good but fit is a little strange. For a 2005 Nissan Frontier, this kit has to be wedged in (hard), in order to fit properly.Once all the screws are fastened tightly, it becomes a pretty solid unit. Aligning the cross bars so that they all are even and not putting strain on the frame takes alot of work, figure on two people and about a 1/2 hour to get it just right.Once installed, it rubs pretty hard against the bed, my truck has the factory coated liner so that may be something the builders didn't consider in their design. I suspect over time, this will wear off the bed liner coating, but since its only at a very small spot on either side of the bed I don't think its a deal breaker.Buy it if you really need it, so far its been very helpful keeping small items from sliding around in the bed.

Love the extra space almost as I love to "compartment" it makes for groceries when folded in. Great instructions with templates and clear language. I did not love the idea of drilling screw holes in the bed, but with the templates it was simple to get them right. I will say I added silicon sealant in the holes when I put the screws in, I want to keep my truck forever! They do have to be assembled, but I think most anyone can follow these instructions and "size" it perfectly to your truck.

Great value. Highly recommend. Easy install. I installed on 2004 Tacoma double cab short bed. Be aware that for this truck you will need the amp research kit that needs to be ordered separately. Followed the instructions and it was a breeze to install.

Bed extender was inadvertently left at dump and could not be recovered. Replacement was exact replica and I was even able to use the same existing mounts. Assembly was fast and instructions easy to follow.