Hydrofoil SE 400 Sport in Dark Grey

Purchased for a Worldcat 255DC with 150 Yamahas. These are easy to install at the sandbar using the supplied hardware, a 7/16" wrench and Phillips screwdriver. I was able to baseline the boats performance prior to installation, but I have not re-evaluated post installation data yet. These were installed when the boat was at full fuel, and an excess of gear and people aboard. One thing I can say for sure though is that it has gotten the boats tendency to porpoise under control, which was the main reason I wanted to install them. They work. Up on plane at lower RPMs and definitely a smoother ride and less fiddling with the trim control. I've been checking the torque on the nuts and have re-tightened a couple times. I will drill through mount these soon since they are of noticeable benefit.

I put this hydrofoil on a 1991 Ranger with a new four stroke Yamaha 150 which weighed 100 pounds more than my last motor. Which changed the ride of my boat. It would come out of the hole at about a 45° angle and plane out. Then it wanted to porpoise at lower RPM 2000 to 3000. After installing the hydrofoil came out of water about 20° quickly on plane and eliminated the porpoising issue. It looks good and it's easy to put on I use the no hole mounting system.

Fitted to Yamaha 225hp outboard on Hydrasports 23WA. Reason for purchase was the 23WA is known to need a little stabilizing help at lower planing speeds, not an issue if going fast, but the seas don't always allow that, the workaround to use the trim tabs. Even so the boat would fall off plane and not get back on without more throttle, then would need to be backed off to prevent it going too fast.... enter the hydrafoil .. I had used one years ago to fix a similar issue on another boat. Install was pretty easy, very easy, backed up to a sandbar, 20 minutes with a socket wrench and a screwdriver and the hydrafoil was installed - note the yammy needed to use the outermost holes. First "real" trial was out the never forgiving Merrimack river and to Jefferies ledge 35 miles out in 2-3ft waves. No need to use the trim tabs, motor trim was all, ride was stable at low planing speeds, if speed dropped below 18mph the boat stayed on plane and picked back up to 21-23mph without intervention. Was able to use the trim tabs as designed to fine trim the boat. Return trip at near low tide with cross currents and nasty swells, no problem, dropped to 14mph and stayed on plane, picked back up by itself so all I had to do was steer, nice! Back in calmer waters I was able to reduce the engine trim and the boat remained stable (no pounding) and picked up to 35mph at moderate throttle. Overall - boat more responsive and stable, less pounding, steering more responsive, able to run at lower (more comfortable) speed while on plane. May lose a bit of top end speed due to extra drag from hydrofoil but then the trim tabs are not down and the boat isn't pounding so maybe not.

This is my 2nd SE 400 hydrofoil. It works great and keep your boat more stabilize. The best part - no drill required to install this hydrofoil.

Added to my Suzuki 150 outboard to help get on plane. It definitely helped. Still not quite as fast to plane as it should be but I think I need to raise my engine a little and should be good to go.

I have put this on every boat I've had. It really works great on pontoons to lessen cavitation. It works great on my deckboat to get it up on a plane. It will plane at 500 rpms less than before, and while it is getting up to speed, the bow doesn't rise up so much. Before, it would rise so far that i couldnt see in front of me until the boat planed out.

Very sturdy and works as promised. Easy to put on, a few modifications for the Evenrude 200, but not a big deal. Looks good too. Gets on plane in no time.

This is with the best hydrofoil on the back of my Ranger bass boat and I have ever used I would advise you take off your old one and put this one on it is worth the money. Great company to work with fast shipping and good quality Packaging I will buy from this company again

Colocado en cola Alpha One II con un resultado extraordinario. 100% recomendable

I havnt owned it very long but I went with the drill mount method and it took about 30 min start to finish. I personally love the way it looks. It feels sturdy so I dont have concerns that it is going to fall off. It's on a 16' bayliner capri with a 90hp outboard 2 stroke motor with a 13" propeller with a 19deg pitch Loaded down with 3 adults and camping gear it still takes a bit to get up to speed but thats just because the motor is on the small side other then that it feels great and solid while up on the plane. If it's just me in the boat it pops out of the water, feels rock solid and I have certainly gained a high top speed. For the price I totally recomend and I plan on buying the se200 to try on my tin boat with a 9.9hp

IMPECCABLE

Great performance but I had to cut a small piece to fit my 50hp honda

Funziona veramente bene riduce i tempi di planata ed anche esteticamente bello da vedere