Direct store Parts DG262 Grill Burner 14 7/8", Heat Plates 14.6" x 4.2", Igniter Kit fits for Nexgrill 720-0830H,720-0888N/S,720-0783E,720-0830X, for Home Depot Nexgrill 4 Burner 720-0830H

My order was replacement parts for my 4 burner grill including burners and flame deflectors. My parts arrived as scheduled. In just 15 minutes i had installed them but they looked and worked so well I took another 45 minutes and did a real nice job cleaning the grill and grates. Look like new, Works like new!!

These replacements parts were much needed for safety to use the BBQ. Made of good quality and very easy to install. Good as new and no worries!

better off buying one with igniters because it is impossible to get screws off old ones

Look identical to original items. Worked very well after installation. Installation was easy after old parts were removed. One part of the removal is especially hard and may require special tools. The problem is that each burner has an igniter attached to it using two small screws. After 2 years of use, these screws have become corroded, and are almost impossible to remove. I ended up grinding several of them off with a side grinder.

I replace these every 3 years or so, the cheap(ish) grill that I bought in 2014 is still going strong. I replaced the grill grates with cast iron ones and the regulator twice and the burners three times so in total the $349 grill with about $140 in maintenance replacements has lasted almost a decade. Seriously worth the money for these, just make sure you adjust them once you replace them, there are videos on how to on YT.

This burner kit was the perfect replacement kit for my Home Depot Nexgrill 720-0830H that had rusted burners. Everything fit perfectly and was a direct swap. To fasten the back of the burners I reused the old cotter pins, so there was no issue there. Using pliers I straightened the cotter pins to remove them.The igniter bracket screws were rusted in place and would not unscrew. To remove the igniter bracket I had to cut the screw heads off with a dremel tool and a cut off wheel. If this is your situation and you don't have a dremel tool I recommend purchasing the igniter kit also. This would allow you to just unplug the old igniters and remove the burner and igniter as a unit. Then you will just plug in the new igniter.To fasten the original or new igniter bracket to the new burners I bought new screws. I purchased 8 new screws at Home Depot (M4-.7 x 10) these the screws that you will need if you can't reuse the old screws. The length of the screws that I bought were 10mm but any length between 6mm to 12mm will work fine.I've used the grill with the new burners kit installed several times now. I have to say that they work great.

Update: these parts didn't last 3 months. Stay awayAfter 4 years of use and, what I consider decent maintenance (outdoors but under a cover, and deep cleaning at least once a year) my Nexgrill from Home Depot (Model # 720-0830H) finally crumbled in my hand as I was cleaning it and getting it ready for the spring this year. At least the burners and the plates did, the structure is still in excellent shape inside and out. I had replaced the original grates with cast iron grates earlier this year ($39 at HD), so decided to try this kit instead of buying a new grill altogether.I had some issues removing the igniters, the screws were shut and I had to drill them out, once I did that and installed the new kit everything fit perfectly, I looked for similar size screws on my "screw bucket", and it cost me half what HD was asking for the same parts, and a fraction of what a new grill would cost. Now my grill is brand new again! I'm expecting it will last at least another 4 years... but I'll update this review if it doesn't.

The parts fit like a glove! These parts also matches many models amd brands. Investigate and don't send all of your grill to landfill because of a few parts. Save the earth and your grill!!!