Large Opening Adjustable Wrench Spanner with Short Handle 4'' 5'' 6'' 8"(4''+5''+6''+8", blue)

Dipped handle and small enough to fit small places

I am a buy once cry once kind a tool owner, i.e. get a quality product and be done with it. That said I purchased this to use in a tool kit I was setting up for a dedicated purpose where I wanted a compact wrench and this works very well for my purposes. It is sturdy, note that the jaws are on the thinner side of what you will find on most adjustable wrenches. This is not a bad thing as in some instances the narrower jaws may make the wrench more versatile. Again it is sturdy and I think if circumstances necessitated it would hold up to use with a short "cheater bar", while the screw adjuster is smooth enough and holds adjustment as well as any inexpensive wrench. As I observed a mild spot of rust on the tool when I opened the packaging I do feel that it has the most rust proof finish so if it will be stored in a humid place or used wet and not dried off after use it could rust.

O.K., let's begin by speaking English. The 6 inch wrench opens to 1-3/8" while the 8 inch wrench opens to 1-3/4 Inches. These wrenches are certainly fine for general, light duty work. The adjustment fitting works just fine but there is "wobble" in the travelling arm when it is moved. Once you have it adjusted it should stay on the hardware your are tightening. The shorter handle is really "handy" for close-in spots like under a sink, etc.If you get these wrenches wet BE SURE TO DRY THEM OFF COMPLETELY when you are finished with your work. They WILL rust (just look inside the right claw to see what I mean)!Not bad for the price. Also, these things are hard to find in hardware stores. Good buy--get them.

This is an excellent wrench for an EDC (every day carry) kit. It's especially useful because it opens up bigger than even a much larger wrench. The price is excellent as well.

When my mom’s Kohler faucet needed to be replaced, I could not find the special tool that came with the original faucet install. This short handle and wide mouth wrench allowed me to unscrew the faucet base nut so I can replace it. All the other wrenches I had could not allow me to turn the nut due to the constricted space.

This product is good for some of the plumbing needs. The opening was large and I was searching for this kind of product for very long time. Overall good for light-duty work.

Great pocket companion. Use daily.Very handy to have on hand

My bike has 6mm Allen axles which should be easy to remove. Turns out I needed a wrench to remove my rear wheel, and I'd be SOL if I got a flat on the road. This 4" crescent wrench is just the ticket!

El producto es útil pero es notorio que no es un producto nuevo o que no pasó las pruebas de control de calidad pues llegó sucio con marcas de dedos y algunas abolladuras. El precio debió ser mas bajo.

Its compact, holds it tightend position well, minimal wiggle on adjustable arm. Wide opening is excellent and truly make the tool useful over a lot of sizes. It compliments as a bolt/nut holder when tightening the other side. While its great for an EDC toolbag, the 4" is small in the hand and in retrospect I should have gone with 5" for the extra leverage. I guess I'll have to buy another one :).Decent quality and good price make it a good value item that you will land up using. Shipping is fast - it got to me in under 10 days.

I needed this to tighten my kitchen faucet that came lose. Regular wrench couldn't get in the tight spaces. This got the job done and done well.

It’s a cheaply priced Chinese made adjustable wrench.. that being said other than the amount of play in the jaw (which all adjustable wrench’s have some, granted this one has quite a bit right out the package) I’ve yet to find an issue with this tool after 2-3 weeks of daily use. For a 4” handle the jaws open quite wide (24mm or about half the length of a McDonald’s chicken nugget for all the Americans) which is wide enough for most hydraulic fittings I need it for when a combo wrench won’t fit. Not a quality tool I imagine but hasn’t let me down so far and for the $10CAD or whatever it cost shipped to the front door you get what you get I suppose. Measurements are easy to read and the grip is decent. Hollow handle for weight savings is nice too.

Yeah, yeah. Right-size wrenches/sockets are what you should be using... But this thing fits in a pocket and is more than good enough to get little things (and then some) done.What you lack in "functionality," you make up in saved walks back to the toolbox. Fits in tight spots, decent quality for what it is... If you think you need a little wrench, just add it to the cart. Totally worth the ~$10