EKLIND 92600 PSD Ball-Hex (allen) Precision Screwdriver - 6pc set Metric MM sizes 1.3-4

I bought 4 sets of allen drivers and needed primarily the 1.5 to 3mm drivers. The summary: the EKIND 92600 precision set definitely is the best if you need small drivers. The small drivers in the EKLIND 90609 set come in second place, with the advantages of really nice bigger drivers as well. The Bondhus are best for 3mm+ drivers but worst for the smallest drivers. The Wiha drivers are OK but are all a little small for adult hands, and the sizes can't be read. The picture shows only the 1.5, 2, 3mm sizes of each set. The individual comments below are listed in the same order as the picture. EKLIND 90609 Ball-Hex (allen) Screwdriver - 9pc set Metric MM sizes 1.5-10 - Up to 10mm was a big plus for me. The bigger handles are really meaty and nice. The smaller ones are OK, not great but at least as good as all the others I tried. The sizes are printed on the side and a little hard to read. The balls can be cut on these to make "non-ball end" allen drivers. EKLIND 92600 PSD Ball-Hex (allen) Precision Screwdriver - 6pc set Metric MM sizes 1.3-4 - These are my favorite of the bunch by far. Rubber coating on the handles, large. A really nice feel in the hand, swiveling caps. If you need the smallest sizes, this is the best set of the bunch. The sizes are molded into the top of the cap. The sizes are OK but could be bigger. The ball ends can be cut off. Bondhus 10686 1.5-5mm Balldriver Screwdrivers, 6 Piece Set - The 1.5 and 2mm driver handles were too small to hold in anything but 2 or 3 fingers and in my opinion would certainly cause hand cramps if used for more than a few minutes at a time. It's also pretty much impossible to read the sizes printed on the sides of these. The 3mm and bigger sizes felt really beefy and nice in my hand; the 3mm and bigger sizes are the best feeling drivers of all these sets I listed here. The balls can be cut off to make "non-ball" drivers. Wiha 26491 5-Piece Ball Metric End Hex Driver Set - Nice quality but a little expensive and small for what you get. I think trying to assemble an entire R/C car with these would quickly result in hand cramps. The sizes are printed on the side but are wasted ink as they are impossible to read. The ball ends cannot be cut off on these but the end material may be nicer; hard to tell. EDIT: I am concerned about the other reviews that say these break or are rounded off. I haven't used these a lot. Keep in mind my intention is to cut off the balls and use them as straight shaft drivers.

These are magic ✨️ They fit snug and allow for easier access to odd angles for my rc model airplanes. Definitely a bonus tool✅️

These are good value, and handle sizes are a good middle ground between precision drivers and full-size drivers. These are nice for medium-scale work like 3d printers and probably RC cars, where you want to spin small fasteners quickly but don't want your hands to cramp up using smaller drivers or hex keys, and you don't want to overtighten things. My only complaint is that the rotating top cap on the handles has some sharp points, probably from where the plastic was released from the mold. These are easy to remove with flush cutters and a small file, but it would be nice if the company took care of this at the factory.

These are really nice screwdrivers. The precision is great, no slop, and they are quite durable. The size is molded into the spinning end cap. The rubberized coating makes the grip secure, it doesn't slip around. Comfortable in the hand, good weight and heft. The spinning end actually spins unlike cheaper tools. Reminds me of old precision tools made years ago. Feels high quality, but for a reasonable price! Made in USA, which is great too.

I’ve been working on a number of projects with some assembly with metric fasteners, and while traditional Allen keys are universal to a degree, never the fastest. I’ve been putting hex driver bits into some of my screwdrivers, and could spin t-handle hex keys, these precision screwdriver style ball-end Allen keys have been a major time saver for me during assembly steps. Lightweight, decent balance, good reach and the ball end fits fairly well to the socket head machine screws I’ve been using, making it a little easier to place the screws. The clear vinyl packaging included with the screwdrivers isn’t much to write about, it works for storing the screwdrivers when not in use, but not the most practical either with some odd folds to keep the tools in place. While I haven’t thrown away the case yet, nor find it work knocking a star off this rating, the screwdrivers have either been loose in my tool at when needed in the field, or looking at adding a screwdriver holder to my workbench or pegboard, and so far the screwdrivers seem to be holding fairly well. If I wear out the tips or handles get loose (which I’ve seen on similar drivers when over torqued) these are affordable enough and work well enough I could see buying these again

This ball hex driver set is fine for light work, but the quality is noticeably lower than premium brands. The handles feel cheap with rough edges, and the sizing is inconsistent. Smaller tips like the 1.5 mm and 2 mm wear down quickly or strip screws with very little torque, which makes them unreliable for precision work on 3D printers or electronics. The larger drivers hold up a bit better, and for the price you do get a functional set that can cover occasional jobs. That said, the shafts and ball ends are softer than they should be, and I have had tips round off after only a few uses. The included pouch is also flimsy and doesn’t add much value. If you only need these for occasional light tasks, they will do the job, but they are not something I would trust for regular or serious use. For long term reliability it is worth investing in a higher quality set.

Nice at first. Then, after very limited use (like ~20 2mm screws), the head no longer fits in my bolts because it’s rounded off. The screws’ material is stronger than these driver :/

One would think pirchasing a good old quality phillips screwdriver would be a rather easy task, right? Well, not so much. I’ve wasted money on so many screwdrivers where the tips are too wide, or too narrow, or too short or too long and end up stripping the head of the screw, or having the screwdriver slip out of the head of the screw while tightening. This screwdriver is exactly what I’ve been searching for all this time. It is solid quality with a good weight, quality handle, and most importantly, the tip is designed in a manner that makes makes the tip of the screwdrivef stay securely in the head of the screw. And, it works great on a wide variety of different sizes of screws

I Brooke one with in 1 week not strong but what do you expect at this price point.

Buen juego de destornilladores Allen con cabeza esférica. Se sujetan bien y tienen el tamaño adecuado para las medidas que trae.

Bought these for a certain job I had to do and they worked as expected. I’ve other Elkind tools and knew of their high quality. I thing they had been priced wrong so bought another set for at work and a set for a friend too. Had them for a while now and they seem to be genuine Eklind as they are standing upto heavy use and fit great.

Great set of ball hex screwdrivers. Works as advertised and good value, especially with nominal delivery charge.

Cost effective, simple compact set to replace my most commonly used hex-keys on my 3D printer - so much better and nicer to use as a screwdriver straight-on rather than thumb-twisting allan-keys in small turns. Rounded tips are of course, a mixed blessing, there are advantages for having them often, but they also can reduce on the surface area enough to be weak on tight, tight connectors, but that would happen with any ball-tip.