GeeekPi ICE Tower Cooler for Raspberry Pi, RGB Cooling Fan with Heatsink for Raspberry Pi 4 Model B & Raspberry Pi 3B+ & Raspberry Pi 3 Model B

Absolutely love it! Looks amazing, fits really well and assembly is easy. I'd recommend using a traditional thermal paste however a thermal silicone pad is provided. The rgb led is permanently on but a black fan was also provided in the kit should that be your preference. Works on 3.3V or 5V pins so there is 2 options for fan speed and led bright brightness. Comes with a white acrylic base plate that does the job perfectly well if you don't have a case on already. Fan I find is very quiet and keeps the processor super cool, perfect for overclocking or just turning your pi into a mini pc ;) Highly recommended all round.

I love how easy and fun it was to put together and install. It fit my 3B+ perfectly. I wasn't keen on the pre installed color changing fan so I swapped it for the included plain black one. They also provided spare screws and fixings in case you misplaced the original ones. The fan is whisper quiet and keeps the pi nice and cool. I love this tower cooler and I am going to put one on all my raspberry pi's. Would strongly recommend.

Quick and easy to assemble, comes with everything you need, including spares. Mounting bracket fits but could have been a slightly better shape/fit. Instructions/diagram are sufficient. Went from 40's and peaks upto mid 60's temp, down to high 20's idle and peaks upto 40, usually sits about 30 under general use (pi case is open top, used included thermal pad to test, im happy with temps so not even gonna bother with using thermal compound) So couldn't have been happier if not for the quality of the led fan lol Was almost silent for a few days, then started to resonate through the whole pi and be not so silent lol. It did come with a standard black fan too, might be better quality? But I like led fans so ordered a replacement lol. The noise still isn't that loud to be fair, although does appear to be getting gradually worse with time, however the vibration its causing concerns me. Still well worth the purchase as the cooler works great, you might get luckier with your led fan too, and there's the extra black one included which may be great? If not, they only cost a few quid.

First I should point out that the box I received had Pi 3 model B on the side label but I had a Pi 4 (worried ....) In the box was only 1 set of brackets not 2 with no label on them (worried more ....) BUT they did fit the Pi 4 as expected (I think maybe the V 2.0 of this product may have a universal bracket set now ?) I used MX4 thermal paste instead of the included sticky pads which worked well. I intended to build a fan controller with a MOSFET but it is fairly quiet and I have not needed a speed controller as yet. Also the V 2.0 fan is not just the blue led but changes colour and intensity constantly, it looks quite cool. The kit also comes with a perspex base plate which is useful and protects the board from scratching the surface it is on as you can't use any case due to height of the cooler. Now for some temperature results :- Pi 4 has no case and is overclocked with overvoltage=6 Arm_Freq=2147 and GPU_Freq=750 (so pushed to the very limit) and running 64 bit kernel. Room temperature at 23 C. When idle on the Raspbian desktop the temperature is 30 C or lower ! When pushed with 'stress --cpu 4 --timeout 360' command to load all cpus to 100% the temperature at the end is only 43 C and drops back below 34 C in a matter of seconds once command ends. The whole Pi 4 is much snappier and very usable for general desktop process now. Only negative is I can't fit the 40 way ribbon cable for my t-adapter/breakout board due to too little gap between the cooler bracket board standoff's and the GPIO pins. I can however run individual pin cables across to the t-adapter which is fine as I don't need that many, never needed anything close to all 40 at any time. The best product I have ever added to my Pi. Edit: I have found that a GPIO header riser fits OK and the ribbon cable for the breakout adaptor can be attached to the riser without any issues.

I hadn't used my Raspberry Pi 4 since it was released. The high heat load and the lack of USB boot meant that I'd kept my Pi 3 working and using that instead. However, seeing this, and that the heat of the Pi4 had been reduced through firmware updates, I took the plunge. I installed and then used the Pi 4. Running at 100% load on all for cores over night saw tempertures only hit 45°C, which is a fantastic improvement over the previosuly seen loads. I set mine up with the attached thermals pads - I didn't have any thermal compound around the house to see what that would do, but I'm happy with the limits I'm at. Noise is reasonable - on my desk, it sounds about as loud as an external drive being accessed, so I have no problems with that. Light wise - it might be nice to have a version without LED's but again, it doesn't really bother me. Overall, very happy with this.

It keeps my Raspberry pi 4 8GB cold. The heat sink feels cold, never felt it becoming warmer even when I make the pi work harder. The fan is taking its power of the tool pins (really the 5V). And it is silent. I have had the pi running 24/7 for a week now, in my bedroom. And the sound is hardly noticeable.

Bütün parçaları tam, eksiksiz geldi. Kurulumu son derece kolay. Rgb renkleri güzel. 34-36c civarında işlemci sıcaklığı var. Fan çok sessiz, yanında rgb olmayan yedek fan bile göndermişler. Kendi heatsink yerine mevcuttaki sıvı heatsinki kullandım.

استبعدت المروحة السابقة وأضفت هذي.. خفضت حرارة الراسبيري من 40 إلى 34

He proba otras opciones que e no me han funcionado. Ésta me mantiene la temperatura de la Raspberry pi 4 a raya y además no se oye nada, teniendo en cuenta que yo soy muy exigente con el ruido. Subte molesta las lucecitas cambiantes que tiene creo que se pueden desactivar. Llevo más de 1 año usándolo y nonhe tenido el más mínimo problema. Lo recomiendo.

Acheter pour refroidir un nas sous rapsberry pi 4, alimenter en 12v assez bruyant par contre en 5v on ne l’entend pas et il refroidit très bien le raspberry