hansgrohe Hot Widespread Faucet Cartridge 1-inch Spare Part in 94009000, N.A, One Size

Replaced my hot water valve since it was leaking. Old one needed a little force to take off. But this one like fits perfectly and works perfectly. No more leaks. Perfect fit for Hansgrohe faucet.

Our Axor Cittorio faucet was leaking small amounds of water from the base of the handle whenever we turned the faucet on. Replacing the cartridge fixed the issue. It also restored a smooth movement to the joystick handle.This cartridge includes instructions for various faucet models, including the Cittorio, which is the model I have. The tool that was included in this kit was useless for the Cittorio. You will need a 1 1/32" deep hex socket to remove the cartridge once you pop off the handle. I ended up purchasing a shower valve socket set that included a 1 1/32" deep hex socket.The kit includes a packet of silicone grease which you should apply to all of the o-rings and rubber seals when you install the new cartridge. I had purchased a small tube of silicone grease because I did not know it was included in this kit.For the Cittorio, you will need a 2.5 mm allen wrench to remove the set screw on the back of the handle. There is a hole in the body of the faucet below the handle that looks like it could be an access point for another screw that you need to remove, but it is not. It is just a small round hold to allow water to drain out of the faucet body in case of a leaky cartridge or gasket.Once you remove the set screw on the handle, you will likely need to pry the handle off, along with the ring that surrounds the base of the handle (the ring with the hot/cold/close printed on it). Don't expect to simply pull the handle off once you remove the set screw. Maybe you can do this if you're lucky, but it will probably be a little frozen in place and you'll need a lttle leverage to get it off. The round dome at the bottom of the handle is part of the handle itself. Though it looks like the set screw might be holding the square part of the handle onto the domed base, the domed base and the square part of the handle are welded together and are one unit that pull off together once you remove the set screw. You may find it easier pry up the ring at the base of the handle first, then pry up the handle itself.There is nothing holding the ring at the base of the handle in place other than friction between an o-ring that surrounds the ring itself and the body of the faucet. I needed to pry the ring up with a very small screw driver (be very careful not to scratch the finish). Try not to damage the o-ring surrounding the ring if you pry it up with a screw driver (you won't see the o-ring until you pry it up). If you do damage it, it's not the end of the world and it will probably still work fine because it is not exposed to any water pressure. I also used a screwdriver to pry up the handle, but you need to be careful so that you don't scratch the finish.Once you pull up the handle and ring, you'll need to unscrew the 1 1/32" hex nut that holds the cartridge in place. You should get a second pair of hands to hold the faucet in place so that it doesn't rotate as you try to loosen the hex nut. It takes a bit of force to loosen it.Once you remove the cartridge, you'll need a pair of tweezers or needle nose pliers to pull up the two small round rubber thingies that sit on top of small springs. You can also use a small screw driver to pry them out of place. You will replace the rubber thingies and springs with the ones supplied in the kit. There are other parts included in the kit that you will not need for the Cittorio model and the instructions indicate which pieces are not needed. Make sure the rubber thingies are seated properly. You'll need to wiggle them a bit to get them over the springs and seated in the holes. It's not too hard. Don't forget to put a little silicone grease on them to make them last longer.The cartridge comes with an o-ring that sits on top of the cartridge when you install it. Don't forget to remove the old o-ring, which will likely be stuck to the bottom of the nut that you'll remove which holds the cartridge in place. I seated the o-ring in place on the underside of the nut when I installed the cartridge, rather than on top of the cartridge itself. I'm not sure which way is better. Make sure you put some silicone grease on the o-ring to extend its life.Good luck!

Perfetta e facile da installare.

Originaldel, så kvalitet/passform är perfekt.O-ringsfett medföljer, men inte alla o-ringar, så några behöver återanvändas vilket drar ner betyget med tanke på priset.Medföljande verktyg är så kasst att det är helt oanvändbart och egna verktyg krävs (i mitt fall en polygrip och en 27mm nyckel).

We have an Axor Starck kithen mixer tap circa 2002! The tap is fabulous quality and still like new however required a new cartridge. This cartidge is a different size to the original cartridge but hidden in the box is a plastic adapter which the cartidge sits in and makes for a perfect fit. So anyone out there with an ols Axor Starck tap, yes this cartidge does fit and works perfectly.