TFX PRO Handgun Sight

Note these are my first aftermarket sights, but I did a lot of research and analysis before buying and felt the TFX Pro was the best option. Your needs may lead to a different choice. Regarding installation, I completed the install on my S&W Shield myself. It took about an hour because getting the old sights off can be a bit of an experience and effort, but the new sights went on more easily, and I also did some fine tuning to get the sights centered. Much of the time was being careful because I was concerned all the pressure to push the sights off and on was going to deform or break the sights, but nope not at all. I did rate the install as 5 stars, but that doesn't mean it's easy. It's just easier than the stock sights and I didn't have any hang-ups during the install. Again, you just need to make sure you still the sights centered correctly. ADVICE 1: Get a good sight pusher. Using the hammer and punch was killing my punches and the sights wouldn't even budge. I could have gone harder but I didn't want to risk marring the slide, so the pusher proved to be much better. Note that I found it useful to clamp the pusher in a vise so it was more stable and less prone to slipping out of my hands. ADVICE 2: Before installing the new sights, use a sharp pencil to mark the center of the top of the slide while the old sights are in place. It will make it easier to center the new sights. I tried to use calipers to measure the center, but it was hard to get a good or consistent purchase when measuring, so I didn't get the accuracy I was looking for. I wish I had marked it. Or having a reputable gunsmith install the sights may be the easier way to go, just make sure they care enough to center the sights correctly. ADVICE 3: Apply a light coat of oil into the dove cuts with a swab so the new sights go on more easily. ADVICE 4: Many pistols have a set screw on the rear sight to ensure it doesn't move. You will need blue thread locker on the set screw so it doesn't come loose. So after the install, I just practiced some draw and and target acquisition. I literally could see an improvement after like 6 draws. It's really easy to get used to, and it's really easy see whether the dots aligned correctly, especially with the orange circle front sight. I wish I bought these a long time ago. I was concerned about the tritium/fiber being too bright when in the dark, but not the case at all. They are low key enough that if you needed to hide yourself, they wouldn't show, but have good brightness to still be plenty visible. I'll still have to try it in mixed lighting to see if the green dots are still easy to make out, not sure. I really liked the rear sight having a ledge that I could use for one-handed racking. It's also useful for my friend, where she doesn't have a lot of grip strength to rack the slide, so having the ledge makes her life easier as well. That's about it. Well worth the price and they look great. Now I'm going to buy more for my other pistols. Enjoy.

I bought these for my G43 because I wanted something I could see in low/no light conditions as well as mid day at the range. I wanted a high visibility, no maintenance, sight for my ccw that worked. These work much better than I'd hope for. The orange ring around the front green sight is perfect for fast sighting in the light. The green glow in the dark is just right. No straining your eyes. Amazing how these work so well across the available light spectrum. If there's a "worst" time to see them, it'd be at dusk when your eyes are still adjusting to the lowering light levels. The fiber optics pick up a lot of light while it's available, but until your eyes adjust to the darkening environment, the sights appear dim, but still visible. Once adjusted the glow off of the sights looks bright. I spun my gun around, unloaded of course, in the dark and was surprised that I couldn't see any glow off of the sights in the dark from the business end. Installing these was a breeze. I used the Truglo front sight tool for the front sight with zero problems. Quick and easy. For the rear I used the Universal Sight Tool Pusher from Sighttool (on eBay, a very well made tool). Quick and easy. I secured both the front and the rear sight screws with blue Locktite 242. These sights are significantly longer than the stock G43 Sights, but only slightly taller. I have a N82 Pro Tandem IWB holster and was a bit concerned that these sights might make contact when drawing or holstering, but there was enough of room. No noticeable difference from the stock sights. I couldn't be happier with the look of these and the function. The one other thing I'd like to point out is the rear sight being angled. At first I didn't think this was an option that could be of much value to me, but after the installation, I really like the fact that you can, in a pinch, jamb the angled part of the rear sight against your belt or a table edge, or what ever is available, and push your gun downward to load it one handed. This is a well though out and we'll built product. Truglo nailed this.

Great sight, works well in daylight and night time. Easy to install with a sight pusher and a socket tool. I have installed this sight on several pistols.

These sights are great! I'm in my 70's, and they make all the difference in target acquisition. After reading the precautions on installing from the manufacturer I watching a couple of You Tube videos, I installed the sights with ease on my Canik TriStar C100. I very impressed at how well they glow in the dark.

These are great sites. I had no issues installing with an MGW Site Pro. They work well for both daytime with fiber optic and nighttime with tritium. The reason for the 4 stars is the Truglo Tritium Pro (no fiber optics) version is NOTICEABLY brighter (2x I would guess). I have multiple of both, and the brightness is very consistent on both "models" of sites. If you are not married to the idea of glow in the daytime fiber optics, DEFINITELY save the 40 bucks and get the Truglo Tritium Pro instead (they are also much smaller).

Superb replacement for old non glowing sights. BUT u less you have the proper tools, work station and strong steady hands just plan on having a gunsmith change the sights out for you, because even with all that these things take a pounding to accomplish. More so the removal of the originals, but both are challenging.

Nicer sights

Amazing sights. Had to modify the rear sight by filing the dovetale to install on my SP-01 Shadow. So be prepared to have it modified by a gun Smith if you own this module. Also do not attempt to install without a quality sight pusher, it will void your warranty if you already haven't done so by filing them to fit your SP-01 Shadow.

Montage Passt, leuchtet im Dunkeln, macht man nix verkehrt. Der Preis ist aber awesome!!! Vergleicht man eine LPA Visierung mit Schräubchen und beweglichen Teilen, viel aufwendiger, kostet aber fast nur ein Drittel. Habe das hier genommen, weil es flach ist und in einen Anschlagschaft rein musste. Nix anderes wollte passen. Visierbild ist halt für Combat / Home Defense usw. Wer Präzi will, nimmt LPA

Best sights I’ve ever had. This is not my first, I actually have these installed in most of my pistols. Money very well spend

Perfect! bright easy to see sights in any lighting condition!!