Orion Motor Tech Power Steering Pump Pulley Puller Installer Tool Set, Pump Pulley Remover Installer Tools Compatible with Ford, GM, and Chrysler

I was helping a friend replace the P/S Pump on his Dodge Ram. He had borrowed the tools from an Auto store where he had purchased the replacement part. After fooling around with the tool that had bad threads and other issues, he went back and got another tool that worked properly. I decided then that I would get my own, and take care of it. This tool works well and the price is great!

Great tool for the rare occasion it is needed. Have used it 4 times and was flawless every time. Price is great.

Worked as it should.

Gets the job done but might not next time. This fit will and worked. I saw someone else's reviewabout using some aluminum flashing as shims and this is great advice. Definitely shim the split clamps in the outter ring evenly with two small aluminum shims. I cut mine from flashing I had on hand. The nose, the piece that pushes on the power steering pump's shaft on my Chevy 5.3L v8, was softer steel and deformed a fair bit. I liberally applied grease to the ball bearing inside and this part. You can see this in the picture with the yellow arrow. I have acess to a lathe so I will make and harden a new piece to replace this part when I'm done fixing my truck. I'm happy this worked the one time on my 20 year old very rusty new england truck. I only picked this tool because it would come 4-8am next day and it arrived at 4:30am. Ifv you are going to use this a lot. Consider a higher quality tool.

Should be zero stars. Not even a worthy toy. Couldn’t pull one pulley, not even close. I’m 175lbs and used wrenches, not impacts. As soon as you started feeling resistance this wax toy starts folding in on itself. Clam shell opened up and just slipped by the pulley nut, and the alignment rod about snapped with barely any force. Don’t know what butter mobile this is made for, but it’s not for real work. Even the tooling is cheap, cast, mild steel. I-rings pre ripped, Threads are rough as hell feeling and the finish is a joke. You’d be best off putting your lips around the pulley and sucking to get it off than use this.

It worked like it should on my 2014 camaro

It does what it is supposed to, at least once. The tool steel is lowest quality, when stressed on a stuborn shaft the tool threads are more of an obstacle than the pulley friction. The tip of the extractor screw separated under pressure, the screw thread deformed and will not go through the puller by hand. Obviously too much force for the toy but I did get the pulley off eventually. I returned it for replacement and try try again.

El Orion Motor Tech juego de herramientas extractor e instalador de polea de bomba de dirección asistida me pareció de muy buena calidad desde el primer uso. Las herramientas se sienten firmes, bien fabricadas y resistentes, ideales para este tipo de trabajo. Lo utilicé para sacar e instalar la polea sin problemas, todo calzó correctamente y permitió hacer el trabajo de forma limpia y segura, sin dañar la bomba ni la polea. Se nota que es un kit bien pensado, con piezas sólidas y roscas que no se barren fácilmente. Por el precio, la relación calidad-precio es excelente, ya que evita tener que improvisar o llevar el trabajo a un taller. Es una herramienta que perfectamente puede usarse más de una vez y seguir rindiendo bien. En resumen, muy recomendable, buena calidad de materiales y excelente opción si necesitas una herramienta confiable para bombas de dirección asistida.

This worked like a charm pulling and removing the CIII Power Steering pump on my 06 F-150. Lightning fast shipping, great price and well built.

As described, worked perfectly and good quality. Thanks G

Used it on my F-350 6.4L power steering pump and it worked great! I had to put some pretty good force on it to get the pulley off the old pump and it held up just fine.

If you didn't know how to this puller, the instructions may leave you scratching your head. They are not very clear. I watched a YouTube video on how these things work so I kind of knew what to expect. That being said, I got my p/s pump pulley removed, so no complaints.

Garbage. Tolerances are off, casting that fits over the pulley is horrible and had a crack in the casting to begin with. Learn from me, just spend the money on a quality one from OTC. I will now cut this up and use it for something else. I keep trying to save money here and there, but all of this cheap off shore stuff just ends up costing more when you have to buy it twice to get a quality one.