Shallow/Deep Well Jet Pump, Cast Iron Convertible Pump with Ejector Kit, Well Depth Up to 25ft or 90ft, 115V/230V Dual Voltage, Automatic Pressure Switch

This is a great pump. I bought it to replace a 1/2 hp shallow well pump that was not pulling water from our fresh water spring. This pump was super easy to install. Already pre wired with a 110 power cord. I switched the pump to 110V from the 220V. Primed the pump one time. Plugged it in and voila, water flowed and filled the pressure tank. It is super quiet. Turns on at 38 pounds and off at 60 pounds like it should. I would definitely buy again. Easy to register for an extra year warranty. 5 stars!!!

The pump has been installed and working properly.

VERY IMPORTANT TO KNOW! ESPECIALLY IF YOU ARE THE TYPE WHO DOES NOT READ DIRECTIONS! 🤪 This is identical to the one we had so hookup was easy. Turned it on, wouldn’t shut off. I know some people (not me lol)think they can just do things without reading the directions hmm Anyway, when it wouldn’t shut off I’m like, where’s the directions? I finally found them, read up on troubleshooting. Guess what? Even though it has a regular plug, it’s set up for 220, not 110! Seriously! Who does that? It said there was a switch in the box, looked all over for it, it’s not a big box, but kept looking lol. Discovered there is a little black box in there that you have to turn over and the switch is on the other side! 🤦🏼‍♀️. Switched it to 110, and now it works perfectly!

Great pump so far we have water. Quick ship after having bad experiences with other brands recently. We have Water!!! Thanks alot for a great product.

This pump leaked like a sieve from the get-go, despite professional installation and re-installation. It failed from the start. The issue appears to be faulty machining between critical seams where the primary gasket fits. Fortunately we bought the Asurion coverage and are returning the item. Save yourself $ and headache and buy a better pump. Hopefully the Asurion return goes well - we have to package up the heavy item and take it to a shipper.

The 3/4" line runs 50' in lake then 25' uphill and into cottage. TIPS: Throw away the rubber gasket that came with pump, and just use a tube of "gasket maker" on each piece to be connected on front of pump, wait two minutes before assembly, then tighten the two bolts. SECOND , in order to prime the pump, the 1 1/4" plug in top of pump is where you must pour water in to prime it. You must install a check valve a short way from the pump. The small hole is on top of pump is an air bleeder. You CAN NOT PRIME PUMP USING SMALL HOLE. At the bottom of the hill, I cut the 3/4" pex line and added a tee, and a gate valve with a female hose adapter. By connecting a hose I was able to fill the entire line with water before priming the pump. I ran a dedicated 110 volt line from panel box. The pump should be on its own 20 amp breaker. It runs fine on 110, but it would be better to run a 240. Last thing, the pump is wired for 110, but if you use 110 there is a little switch you move to 110, it comes set for 220. The cut in pressure is 20lbs, cut out pressure is 40, so the air tank needs to be pumped up to 18lbs. The pump works fine, great value for the money. I also purchased a separate kit with pressure gauge, relief valve and tee for connections to pressure tank. I made the job easy. I started by using 8 large cinder blocks stacked 4 wide and two high for a platform. Five stars for the pump!!!!

Bought this pump to draw water from a canal to run yard irrigation. Installed the pump on a dock with 1-1/4” pvc drop pipe and foot valve in the canal, drawing water from 1-3’ below dock, depending on tide height. Foot valve is positioned off the bottom of the canal, with total drop pipe length of about 8’ total vertical drop from pump elevation to pipe opening and foot valve. Pump outlet goes into a 1” discharge pvc with a manifold connected to 3 faucets to hook up hoses approximately at the same level as the pump. I will eventually instal permanent in-ground irrigation system, but, for now, I’m dragging 5/8” gardening hoses connected to spike-type impact (Rain Bird) heads. Pump instal was easy. I mounted the pump to a stand attached to my dock, switched motor to 115 v setting, and filled impeller assembly with water. Pump quickly primed and pumped water directly after plugging in the power cord. I did have to adjust the cutout pressure side of the switch to prevent continuous short cycling as pump is apparently shipped with cutout at about 40 psi. Once done, the pump will keep up with the 3 spikes at about 42 psi, according to the installed pressure gauge. I checked the specs on the impact heads, and each is rated at 3.1 gpm @ 45 psi for a total of 9.3 gpm running all three heads. I added a fourth head, but pressure drops to less than 20 psi, and that is too low to make all 4 impact heads cycle properly and throw distance of water also drops significantly. I then checked gpm output of the pump using a 5 gal bucket with no heads attached (that is, I opened all three faucets directly into the bucket, timed fill rate and divided accordingly to produce the gpm). Three separate tests worked out to calculate a gpm rate for the pump at about 10 gpm with full open faucets and about 15-20 psi. Closing the faucets slightly will increase pressures, but drops gpm to about 9 gpm at 40 psi. Bottom line: this is an inexpensive pump that will work for small irrigation projects, but don’t expect it to meet the expectations for gpm published with the pump. Specs list hourly output at 1,200 gals, which converts to 20 gpm assuming 1,200/60 mins = 20 gpm. Truth is , actual gpm is about half of published rate. The pump seems to run fine otherwise and is only moderately loud as pumps go. As I get to the irrigation installation, I will use sprinkler heads suited to “dirty water” with interchangeable nozzles to accommodate reduced gpm of the pump.

After struggling for a year with another pump, I purchased the Acquaer Shallow/Deep Well Jet Pump and within minutes of hooking it up, I had water! The pump was very easy to install, is very quiet and runs like a champion.

Installation facile, bonne suction et poussée. Je l'utilise pour arroser ma haie de cèdre 2h à tout les jours depuis 3 mois déjà et elle fonctionne très bien! Ma pointe est située 30 pieds plus bas dans un cours d'eau et je n'ai aucune difficulté. Vient avec la pointe et les accessoires pour l'installer en simple ou double tuyau.

Pump as advertised, appears to be well made. Installed the pump and works well. Thanks

Quite and lots of water pressure!

So far so good! Better design at all levels, it even comes with cable and plug! It needs a third mounting point/bolt for over the tank installation.

Je suis ultra déçu de set pompe Pompe pas vraiment Il fait un train danfaire dans maison Je veux avoir un remboursement