Dual Motion Sensor Light Strip Indoor Under Bed Lights Warm White 16.4Ft | Motion Activated LED Strip Lights, Auto On/Off, Two-End Motion Sensors Night Lighting 12V For Bedside Stair Cabinet Hallway

I purchased these to have motion lighting under my bed. We had an adjustable frame that had motion lights and we decided to replace it, well the one that we replaced it with has lighting but they have to be turned on by the remote. We have a small furbaby and we like to know when he starts to move around at night so we don’t step on him so motions were not an option for us. The install went very well and easy until I got to the part where I needed to cut the light strip and use the connector 😬. This is very important for installation and I’m handy but I couldn’t figure it out. I watched a you tube video and I finally got it. To connect the lights via the cable you must place the cut end of the strip underneath the silver prongs on the connector and close it for a secure fit or else the lights won’t work properly and oh you must open them up too! They have a little groove on the connector that you must open. The instructions doesn’t show that part. If you look at one of the photos you will See what I am talking about (see the 1st photo). Now that they are installed I am loving them! Also these come with two sensors so you can put one on either side of your bed. Once you connect them when one sensor is tripped all of the lights come on simultaneously. Also a big plus they operate by electric not battery so u don’t have to worry about changing a battery at all!! If you are looking for unserved lighting I highly recommend them!

I wanted motion activated lights for my stairway and this LED lighting strip provided two motion sensors, one at each end of the light strip. It's sufficiently bright for this, and just plain white light. I didn't want to light up my stairway like the Vegas strip with flashing, chasing, or colored lights. Just not my style for my home. So it's a perfect solution. I had three problems to solve. First, the strip would have to be shortened for it all to be hidden under the stair rail, and the kit doesn't come with connectors. Second, I wanted to minimize "false triggers" when walking past the stairway and not going up or down it. And third, the nearest outlet was too far away for the supplied cord. I cleaned the stair railing bottom, then wiped it with rubbing alcohol. The adhesive on the LED lighting strip sticks really well to a clean surface like this. I just ran the LED strip over the supports on the underside so I didn't have to remove the railing. I had to cut a section out to avoid having it too long. I bought RGBZONE 8mm 3 pin connectors here: https://www.amazon.com/dp/B0C6KW7TX7/ and they worked great to connect the strip back together. After positioning the motion sensors I used black electrical tape to cover half of the sensor. It took a couple of tries, but I covered it enough so that the light strip doesn't come on until you step on the first step. The top sensor, tucked partially behind the railing, is shown with the electrical tape on it in one of the images. My nearest outlet was a few feet away so I bought an extension cable "2-Pack 10ft DC Extension Cord 5.5mm x 2.1mm" by Weformy here: https://www.amazon.com/dp/B09Q7V9GGQ/ It worked great. I'm very happy with the result.

Overall was easy to install and plenty long enough to wrap all the way around my king bed to night stands and power cord was plenty long enough. Motion detectors are almost too good! Have to keep CPAP hose up and away from the motion detector on my side so the light would not come on when not intended to be on. My only 2 things I wish this had was the ability to change the length of time before shutting off as well as brightness control, had to add a dimmer to it (one of the images shows a dimmer and it says do not touch with wet hands, but the dimmer is not included in this kit).

Worked great for about 3 weeks and then 1 motion sensor just stopped working! The other side is working fine but you need to walk all the way to the other side of the bed to activate.

I got this for my dad so he can see at night without having to turn on the hall light all the time. It works exactly how it says. So what and how to fix: 1. It is dimmable! You need an RF LED light remote for led lights. 2. Use what comes in the box. Everything comes in the box. The only other thing you might buy is the corner joiners. 3. If you cut it wrong you could cause a short. The short is harmless, but it might short circuit the lights. And for God sake didn't put a nail threw it! 4. LED are power sensitive, don't use another plug if you are not sure if the wattage and amps. Normally they only work with 1 plug but some cheaper ones use the same plug with different watts and amps. 5. Don't put it on a light switch. It's not designed for a switch, because it has a switch. You are just wasting it's usage. LED are not perfect, if you have a short or problems read and then contact the manufacturer. The manufacturer cannot know how it will work in different environments. To much heat may give it a shorter life span, while colder may draw more power. But the life in LED should be measured in years, not hours.

I wasn't prepared for how bright these are. I put them on my bed before plugging them in and holy cow your whole room lights up. Too bright for me and there's no dimmer like the last under bed lights (which broke because.... Children.) these lights are fine but I've resorted to covering up 3/4 of the LEDs with electrical tape. I know, not fancy but no one can see it. I so tried out using some aluminum duct tape which works great but is more tedious. I have lowered my review score to me because I ended up taking these off the bed and putting them in a closet and buying the ones with a dimmer. It's just stupid how bright these are.

Thought this was going to work. I installed it in the morning. And it came on and turned off. I thought it was going to work great. Later in the day though I noticed it wasn't turning off. I checked the ceiling fan, and anything else that might create movement. No luck, I had to unplug it. I plugged it back in and it will not turn off. Unfortunately I threw the package away, so I don't feel right returning it. It just doesn’t work like it is supposed to.

These motion sensor light strips are such a smart little upgrade for the bedroom! Installation was super easy—the adhesive backing sticks well, and the strip is flexible enough to place neatly under the bed frame. The motion sensor works perfectly; as soon as I step out of bed at night, the lights turn on softly, giving just the right amount of glow without being harsh or blinding. I finally no longer am bumping my leg on the end of my bedframe at night when I get up to go to the bathroom or check on the baby in the middle of the night. The brightness is adjustable, and I really like the warm tone—it feels cozy and doesn’t disturb my partner when I get up. The auto-off timer is convenient too, so I don’t have to worry about wasting power. It makes nighttime trips so much safer and easier. Honestly, I wish I had bought these sooner. A simple idea that makes a big difference!

Me gustó el producto por el doble sensor de proximidad el único detalle es que no es tan sensible, pero cumple su función

La tira se ve muy bonita, pero no sirve el sensor del final de la tira y la luz nunca se apaga, sólo se atenúa y al moverte se prende con mayor intensidad Ya sea de día o de noche siempre está prendida