Hilitand 4-Channel MOSFET PWM 3-20V to 3.7-27VDC 10A Driver Module PLC Amplifier
Thumbnail 1Thumbnail 2Thumbnail 3Thumbnail 4Thumbnail 5Thumbnail 6Thumbnail 7Thumbnail 8Thumbnail 9

Hilitand 4-Channel MOSFET PWM 3-20V to 3.7-27VDC 10A Driver Module PLC Amplifier

4.0/5
产品编号: 150387592
安全交易

细节

  • Item dimensions L x W x H
    2.17 x 1.97 x
  • Voltage
    27 Volts (DC)
  • Manufacturer
    Hilitand
  • Maximum Supply Voltage
    20 Volts
  • Minimum Supply Voltage
    2E+1 Volts
10A Power Output
🔌3.7-27VDC Range
🛠️PWM Control

描述

🔧 Power Your Projects with Precision!

  • REAL TIME FEEDBACK - Stay informed with input and output indicator lights.
  • STABLE PERFORMANCE - Experience unparalleled reliability with high-quality optocouplers.
  • USER FRIENDLY DESIGN - Installation is a breeze, even for the non-tech savvy.
  • VERSATILE APPLICATIONS - Control everything from motors to LED strips effortlessly.
  • ROBUST ANTI INTERFERENCE - Enjoy seamless operation with complete isolation of input and output.

The Hilitand 4-Channel MOSFET PWM Driver Module is a high-performance amplifier designed for controlling various high-power devices. With a voltage range of 3.7-27VDC and a robust 10A output, it features stable performance, easy installation, and versatile applications, making it ideal for both hobbyists and professionals.

Large manufacture image 1
Small manufacture image 1Small manufacture image 2Small manufacture image 3Small manufacture image 4

有问题吗?看看别人问了什么

Is there a schematic available for this part?
Looks like a handy board. Anyone know what the opto IC manufacturer and part number are?
Does it really need pwm signal to control it, or just any gpio signal would do? since it's just on or off, no need to dim the load.
Do you need a fuse between the device (say a motor) and the output of this board, or will the board handle any power issues?

评论

4.0

全部来自已验证的购买

H**T

Excellent and effective

This product performs exactly as expected. I used it to amplify pwm signals from a PLC to operate hydraulic solenoid valves in a project I have been working on. This replaced very expensive proportional solenoid valve controllers, and it works well.

R**R

NOT A 3.3V INPUT

Beware that you need to hack the board to make it work with 3.3V devices, such as ESP32.The PC817 optocoupler input has both 4K7 resistor and 1.6V LED connected in series.With 3.3V input that results in optocoupler input current about 0.36 mA - too low.One way to make this work is to replace 4K7 resistor with 510 Ohm resistor.Which results in optocoupler input current about 3.3 mA.

N**E

Gets the job done but lacks quality control

Great little product. It could use better quality control and better terminals though. I found one of the outputs had an IC leg that wasn’t soldered fully. It was easily fixed but took a little bit to troubleshoot. The terminals are alright, though I would prefer just a flat tip only screw head. Don’t even bother with trying to use a Philips screwdriver either, doesn’t work at all.

M**E

Does not work at 3v

this device doesn't work as advertised with a 3v PWM input. I don't know why i did not read the reviews. I usually do, shame on me

G**F

Definitely works well.

I used these for work for testing mechanical switches.Used two of these FETs to drive 1 million solenoid closures to test some handle bar switches.Ran for days start to finish with no issues.

M**R

Finally! A 5V to 12 V interface!!

So I am going to give it five stars for now. I am running a test to see if the Mosfets get hot or not running an automotive 30 amp relay coil. So far the board is ice cold!!Ive been writing code and developing systems around Arduino and Raspberry pi controllers. This is first interface I have found that can run an automotive type relay. The only thing on market are relay boards with non removable relays. This is stupid to run a relay to power a relay. The relays on these boards are only capable of 10 amps and if any one of the relays go bad the inter board is junk unless you can solder a new one in place. 10 amp relays are not enough for general use, you need a relay capable of twice the load of what ever you are trying to run. Most automotive hardware is 8 amps. The relays on these junk boards are not adequate, you need to use the wimpy relays on these boards to signal a real relay with generally 30 amps. Now you can power something directly from a 5 volt logic controller!!So far this board looks good. Its build quality is very solid, it shipped to me very fast. I was surprised how fast it got here.To the vendor do not ever discontinue this product! Please expand this to an 8 channel and even larger. Get us shields that will plug into an Uno R3 Please. This is the interface we are all looking for not weak non replaceable relay boards.

R**.

Good product. Works very well.

Used this board to power motors from an Arduino and it worked very well.

N**Z

Had to modify to work with 3.3v input from kl25z

The input LED would light when the KL25Z sent a 3.3v signal, but the output FET would not energize. I shorted out the input led and they started working. I am sure they would work fine with a 5v signal.

常见问题

TrustPilot

TrustScore 4.5 | 7,300多个评论

阿卜杜拉·B.

正品,价格实惠。国际送货也很快!

3 周前

Sneha T.

我收到的产品完好无损。总体来说服务很棒。

1 个月前

全球购物,通过 Desertcart 享受优惠
物有所值
各种产品的价格具有竞争力
全球购物
为 200 多个国家/地区的 3 亿多购物者提供服务
增强保护
深受全球购物者喜爱的值得信赖的支付方式
客户保证
深受全球购物者喜爱的值得信赖的支付方式。
沙漠车应用程序
随时随地随时随地购物。
HK$182

关税和税费包括

Hong Kong店铺
1
免费退货

30天对于 PRO 会员用户

15天无会员资格

安全交易

TrustPilot

TrustScore 4.5 | 7,300多个评论

Ayesha M.

产品与描述完全相符。对我的购买非常满意。

5天前

Meera L.

交易顺利,产品完好无损地到达。

3 周前

Hilitand 4 Channel Mosfet Pwm 3 20v To 3 7 | Desertcart Hong Kong