Front White LED Side Marker Lights for Hon'da Civic 10th Gen 2016-2021 Coupe Hatchback with 2Pcs T10 Light Bulbs OEM#H02551127N Clear Lens

These side markers look great but I already got some condensation in the lens. Still a nice looking product

I love it, my friend had no problem installing it and it blends in with my custom head lights and custom fog lights.

It wasn’t that hard to install but I couldn’t install the wiring for the sequential lights because I was too confused where I needed to put the wiring and there were no instructions. It still looks good though without the sequential lighting.

Great product, really changed the look of the civic for 20 bucks. Easy install there is a bunch of YouTube videos to assist

Very good, God Blessing

I bought the smoked ones that do not color change. These have no wires, you just plug your T10 bulb in socket into it and directly replace the existing amber side marker.Aesthetics:* I initially didn't like the raised portion but it matches the stock headlights which also have a raised portion.* The white LEDs included are illegal in my state.* The set looks much better smoked, I originally wasn't sure having a light source behind anything smoked was a good look, the amber halogen gives it a muted look that looks really good.Quality:* It has DOT markings cast into it and at least for the driver's side the marker was an exact fit. A combination of pushing on it (maybe at a diagonal angle), resulted in an audible snap and it was firmly seated with zero play, very satisfying.* The passenger side was a different story. Looks same as driver side but the bulb socket wouldn't turn to lock in at ALL. I was trying to turn it so hard I thought I was going to break the socket. It appears the passenger side was built with defective tolerances on the locking lips (they're too thick). I ordered a replacement but it was taking too long so I just decided to return the whole set and get a different brand.* The dimensions are not the same as original OE. It's thicker on the back side and it's missing the hollow wind or water channel along the wheel well edge the OE have. I would think there's a reason Honda made it thinner and added a hollow channel into the originals, not having them might be detrimental in the long run. I can only guess but maybe the thinner back of the originals prevents ice from water behind the side marker expanding and popping it out? Or maybe if the back of it is right up against the bracket (like these would), it would sandwich water between the bracket and the back (by surface tension) and lead to rust? Any time water is sandwiched between two surfaces it takes much longer to evaporate than water sitting out in the open/air. The missing wind or water channel is questionable as well, seems like it would route water from the fender above down to the wheel well for drainage, this channel was intentionally built into the OE markers, it would have been easier for Honda to not do that so there must be a reason.* Other sets come with tape on the socket for keeping dust and dirt out before you put your bulb in, these didn't have that. Not a big deal, they're just side markers and they're small, you can clean them out with compressed air or water unlike a big headlight assembly.Installation Tips:1. Make sure you push until you hear a snap or you feel it hit home. To make sure grab it on the side that faces the wheel well and lightly pull toward the outside of the car, if not fully seated it will fall out with a little effort.2. For passenger side I just removed one screw (the one below the side marker), which allowed me to peel the liner back enough (maybe one inch) to stick a long flat head screwdriver in, push the tab while LIGHTLY pulling the side marker outward from the wheel well side. If you don't want to damage anything, wrap masking tape on the tip of the screwdriver.3. For the driver side you can access the clip from the engine bay if you don't have those aftermarket side covers. Open the hood and look between the engine bay and fender, near the headlights and you can see the side marker. If you can fit your arm or hand, you remove it by pulling on the clip with your finger (toward the front of the car, because if you were doing this from the wheel well, you would push the clip in toward the front of the car). The screwdriver from the wheel well is probably easier though.4. On mine when I removed the side markers I noticed the original have spacing nubs on the back since the markers are thinner, they need to bridge the gap between the marker and the bracket. These nubs rubbed through tiny spots on the painted bracket over time, causing very light surface rust. I put a little grease on those areas before re-assembly. You can also put touch up paint and then grease if you want.

Fit as expected

The media could not be loaded.  It looks better and adds the blinker functionality to the car.

La calidad del plastico se siente muy buena, no se rompe el clip aunque apliques presión para encajar en donde debe ir, este pieza es extremadamente facil de quitar y poner. CUIDADO AL CONECTAR EL FOQUITO LED, TIENE SU LADO POSITIVO Y NEGATIVO, PRUEBA QUE ENCIENDAN ANTES DE PONER LOS TORNILLOS.