2PCS TMC2208 V1.2 3D Printer Stepper Motor Driver, Upgrade TMC2208 Stepper Driver Module with Heat Sink Screwdriver for 3D Printer Controller Mother Boards Reprap MKS Prusa i3 Ender-3 Pro
Thumbnail 1Thumbnail 2Thumbnail 3Thumbnail 4Thumbnail 5Thumbnail 6Thumbnail 7

2PCS TMC2208 V1.2 3D Printer Stepper Motor Driver, Upgrade TMC2208 Stepper Driver Module with Heat Sink Screwdriver for 3D Printer Controller Mother Boards Reprap MKS Prusa i3 Ender-3 Pro

4.4/5
产品编号: 231208293
安全交易
Peak current 2A
🔇Ultra-quiet operation
🔧Includes screwdriver
经常一起购买

描述

🚀 Elevate Your 3D Printing Game with Silent Precision!

  • PRECISION CONTROL - Enjoy flawless motion with 256 subdivisions for smooth and accurate prints.
  • USER FRIENDLY SETUP - Includes a handy screwdriver and stackable headers for effortless installation.
  • SEAMLESS COMPATIBILITY - Easily upgrade your existing setup without the hassle of redesigning your electronics.
  • POWERFUL DRIVE CAPABILITY - Achieve peak performance with a robust 2A peak current for demanding applications.
  • WHISPER QUIET PERFORMANCE - Experience the serenity of ultra-quiet 3D printing with stealthChop2 technology.

The TMC2208 V1.2 Stepper Motor Driver is a cutting-edge solution for 3D printing enthusiasts, offering ultra-quiet operation, high peak current capabilities, and seamless compatibility with existing electronics. Designed for precision and ease of use, this driver module enhances your 3D printing experience while reducing heat output.

评论

4.4

全部来自已验证的购买

R**N

Amazingly Quiet!

I upgraded my DIY motorized blinds from DRV8825 to the TMC2208 and I am amazed at how much quieter these are than the DRV's. I mean, it is night and day. And they are almost 100% pin compatible. There is no sleep or reset pin on these but the step, direction, enable, microstep, motor,and voltage pins are all the same. One limitation though, the only way to go into full-step mode is to use them in UART, which I didn't want to go to the trouble to do so I am running them in half-step mode and they are still just as quiet. Just apply your VCC to the MS1 pin to get the 1/2 step setup.Also, they probably wouldn't have been a problem but it appeared to me that the solder joints on the top of the pins got too close to the heatsink for my comfort. So I trimmed them with my micro-cutters before applying the heat-sink to give extra clearance, just in case. And you will need the heatsinks. These do get much hotter than the DRV's.

R**M

Works prefect on my Ramps 1.4 in standalone mode.

These TMC2209's saved me from upgrading to SKR controller. They are very quite and smooth on the Ramps 1.4 controller. On mine the tiny pot looked liked it wasn't turning or adjusting ref voltage. Looking close I found I needed a small flat blade screwdriver to get snug in the slot. Adjusted all three (I already had one on hand) to about 0.6 volts. Great upgrade any easy to do.

A**4

Work Great!

These come in their own individual anti-static baggie with a screwdriver and a large aluminum heatsink that you have to stick on.They work great on my Anycubic Mega S 3D Printer and plug directly in where the old ones go, but you will have to swap the Motor 1 and Motor 2 phases on the motor connector that connects to them if you are doing something similar.The heat sink also sticks up higher than anything that it might replace, so you may have to modify cooling fan brackets and similar depending on what type of equipment you are installing these into.

C**S

Runs a

It took a while to get it properly configured with my arduino, but it is running fine now. It is so quiet that I didn't know that it was working for a while since I thought that I would hear it. I added a flag on my stepper and saw it moving.You have to ground the enable pin which is what held me up.

D**N

You’ll wonder why you waited so long.

These are amazing. I wish I would have upgraded to them sooner. They’re a drop in replacement for the A4988 drivers and make the printer SO MUCH QUIETER. I really wonder why I waited so long seeing as they’re so inexpensive. I only upgraded my x and y axis since the extruder and z axis don’t really make noise anyway.

A**R

Works as described

Not much more to say. Works as described, absolutely silent upgrade for 3D printer stepper drivers.

C**R

Ok, but big flaw in design

The driver comes with a screwdriver and heat sink and does seem to work. The problem is adjusting the current to the stepper motor. The screwdriver does fit into the hole, but the potentiometer was not designed to adjust from the top of the board. The only way to adjust is from the bottom and you can’t do that when it’s inserted into the socket on the main board. Not sure how to make the proper adjustments.

Y**1

Got a broken one.

One of the motor driver doesn't work appropriately.

常见问题

TrustPilot

TrustScore 4.5 | 7,300多个评论

Rajesh P.

当我对产品有疑问时,客户服务非常出色。

2天前

拉维·S。

我很喜欢这里提供的多种产品。一定会再次光顾。

2 个月前

全球购物,通过 Desertcart 享受优惠
物有所值
各种产品的价格具有竞争力
全球购物
为 200 多个国家/地区的 3 亿多购物者提供服务
增强保护
深受全球购物者喜爱的值得信赖的支付方式
客户保证
深受全球购物者喜爱的值得信赖的支付方式。
沙漠车应用程序
随时随地随时随地购物。
HK$179

关税和税费包括

Hong Kong店铺
1
免费退货

30天对于 PRO 会员用户

15天无会员资格

安全交易

TrustPilot

TrustScore 4.5 | 7,300多个评论

阿里·H.

发货快,包装精良。Leatherman 工具手感非常高档和坚固。

1天前

拉维·S。

我很喜欢这里提供的多种产品。一定会再次光顾。

2 个月前

2pcs Tmc2208 V1 2 3d Printer Stepper Motor Driver Upgrade | Desertcart Hong Kong