HUANUO CPU Holder Under Desk Mount - Adjustable Wall PC Mount with 360° Swivel, Heavy Duty Computer Tower Holder Holds up to 22lbs

I searched long a hard for an economical and versatile CPU mount. This is by far the best for the money! Not only for the money but really a very good option even at a higher cost. Similar mounts were twice or three times the price. This was even less expensive then just a plain mounting plate.It can hold a full size CPU or adjust down to a small compact CPU case. Mount will pivot 180 degrees, even though likely all you need is one mounting position. Mounting can be the classic way which allows pivoting or a fixed mounting on the long side of mount. It is supplied with wood mounting screws and drywall anchoring inserts and screws. There are stick mount soft round tabs to place on the inside of mount to allow secure non slip inserting of CPU which also protects CPU case from scratches.The supplied allen wrenches fit the adjustment screws as needed. You will need a flat head and phillips screw driver, and power drill to set the mounting hardware correctly. The install is easy, I recommend using a sharpie to mark holes and outline of mounting plate, for ease, if under a desk or not visible later. I mounted a large CPU under a powered sit/stand desk which had steel support bar running the middle length of the desk. This metal support bar creating a situation where I had only one way to mount CPU. With only one way to mount the mount I found I needed to mark the holes, pivot the mount 45 degrees, then setting the screws, and after pivoting back to desired position (which covered the mounting screws on one side, thus marking the holes) was the best way. With smaller CPU's and more space there will be many options, likely any option needed.My experience with installation was very good, the mount is strong and adjustable to just about any CPU, with clear instructions. I purchased 1 first and 15 later because of the great price, I would highly recommend!

I used this to store my CPU under my sit stand desk so that all of the cords were not affected when I raised and lowered the desk. It was easy to install (drill bit for pilot holes was the most “advanced” installation step). It works exactly as I expected/needed and as a bonus I have more room on my desk.

Installed on my Jarvis Fully Standing Desk as it appeared to be more or less an identical design to the "Official Jarvis" one but at 1/3rd the cost.The pros are that it doesn't have that ugly logo on the CPU Holder, which probably means that these are mass marketed which usually means the quality is more or less the same.I cannot speak to the screws provided as I used the ones that came with my Jarvis to ensure that I didn't drill through the desk.At this price point its a great value, I would have liked to have seen the adjustable holder be slightly longer to give more stability to the CPU being held, but at this price point this is the best you're going to find. I personally do not use the swivel feature much, it is a little stiff, but because I do not use it I actually prefer that it is a little more stiff.One thing that might have been nice to include would be a PDF of the mounting plate and its hole configuration. In this particular case I did not need it but I could see where other projects might want to understand the placement prior to making a purchase or even drilling.I would buy again if I needed a second swivel holder.

This is a great and sturdy CPU holder.Pros-Moves 360, so you can easily remove the cables by not getting too deep under the table.Great quality and good heavy metal material.Has good instruction manuals if you understand.Cons-Cannot do it alone as its a bit heavy, my table has hardwood so with me holding the stand and installing screws was tough.I had to make markings and then hit the screws down from below the table.Make sure you use the additional washer/bolts with the screws because if you don't the screws will drop. I did that mistake and ended up drilling holes at a different location.Another mistake I did is i put the holes at the very edge because I needed leg room and don't like the CPU hitting my long legs. So i have locked its movement because of the side bar(see pic), but I don't really care about the 360 move as I setup my cables well and once in a while add some extra/additional USB mice.If you don't need the 360 degree move don't worry about where you are locating the holes to drill..Overall, I'm not a carpenter or a pro and wooden installs so for me this was moderately tough. So take the required precautions and help while installing and don't hurt yourself when doing it. If you have the required experience or at least plan it well, its a easy... Well and its made in China... If you don't like it don't buy it, i didn't have a good option or I would buy a made in anywhere else in the world.

I needed something sturdy to hold a 1500VA UPS; I looked and finally decided on this one. When it arrived, I wasn't sure it would work for my situation, but I moved forward and installed it. I'm delighted with how sturdy and now it adjusts to fit the UPS. It fits my purpose perfectly and keeps the heavy UPS solid during desk motion. I'm happy with the purchase.