Corsair 7000D AIRFLOW Full-Tower ATX PC Case (High-Airflow Front Panel, Three Included 140mm Fans with PWM Repeater, Easy Cable Management, Spacious Interior, Customisable Side Fan Mounts) White

Ok to start with this is the best case i have ever had, also the biggest by far but it gets the job done, so there is a couple of things to know about this case, firstly is that the side fan mount only supports 4x 120mm and not 140mm fans. More than sufficient, also when i first used this case it did sound like a jet engine roaring, this was due to the built in fan splitter and my bios settings. The built in fan splitter must be powered by a sata power cable (same as the ssd to power supply cable), the issue turned out to be that the header i used for the fan was set to DC and not PCM, this meant it was firing all fans at max speed instead of a controlled curve. This one change in my bios made all the difference.Cable management has a lot of room and mounts for the fans come off completely for easy fitting of fans, just make sure when you mount the fans they are in the correct orientation and the cables are in the correct position to allow tidy cable management. You get some complimentary screws and tie wraps plus velcro cable tidies which is great, i never used a manual to figure out how to set up the case for my build as it was self explanatory and things are built in a way to make your life easier.I suggest you pick a place with a lot of space for your build as these doors open on hinges and i needed half a room to have both doors of the case open at the same time, i also found that my power supply cables were not long enough to reach things like my cpu and even my 24 pin so i did have to buy a cable extension kit to get around this. Also although i had lots of room for cable management i still found myself fighting with cables, this was due to cable extension connections being at the back, also the fact i am using a lot of fans. I moved the rear stock fan to the front so the front has 3 140mm stock fans, the rear has a noctua 140mm fan, the top has 3 noctua 140mm fans and the side has 4 120mm fans so you can imagine i am running a lot of cables. (case only comes with the non rgb 3 stock fans, the rest i bought separately)Although i needed to buy a PCU extension kit, change a bios setting, fight with cable management i will say this case is definitely worth every penny, it is very well made, strong, everything is designed to make your life easier, it looks great, it keeps my temps low on cpu and gpu and has plenty of space for anyone wishing to run a custom water loop. I only mention my building issues as i wish i knew before i started so i didn't have to wait an extra day for cables and google the hell out of the fan splitter to find it was a bios setting so i hope someone will read this and it will help them if they need it, otherwise my advice is, DEFINITELY buy this case, it is amazing!

This case was my first choice for a mega build of mine which includes the MSI RTX 4090 Suprim Liquid X, which is a graphics card with an all-in-one liquid cooler combined. I wanted a system that would perform at the highest level without ever reaching its thermal limits, and so I wanted FANS.This case, along with the GPU's radiator, still holds a dozen other case fans so there is ample airflow through out every single area of this case, cooling all of the components nicely.I have a cat that spends most of his time in the same room as my PC, and the thing that impressed me most was after one month of having this PC operational, I went to clean it expecting half a metric tonne of cat hairs inside the case. To my surprise, there was literally NONE. Not one single hair had found its way past the fan filters included in the case by Corsair. All I had to do was clean off the dust and cat hair from the fans, then brush out the finer dust that collected at the bottom of the case. Every component still looks almost identical to when I put it together.A really, really impressive airflow case, and to top it off it's a sleek and elegant build with a full glass panel allowing me to enjoy my own handiwork. I would absolutely 10/10 recommend this to someone looking for a new full tower case.

First want to start with this ... I want it to return the case because my motherboard x570s MSI edge didn't fit in this case , I was waiting near 2 weeks for Hermes to show up and picked it up but of course this company prove again that are soоо bad ..but in this case I want it to give another try and reassemble again my pc and try one more time turns out I need to push a little more my motherboard further so my pre installed IO shield align properly, then all the rest was joy to build didint realize how joyfull is to build in a case that has plenty room , so easy my 420 LFII fit perfect with push pull on top and stay just above my VRM,just need it to push my CPU power cable at left side so the fans can fit then I put 3x140mm Arctic ARGB on front , fantastic fans btw and yes I want to confirm that you can put 3x140mm fans on a side aswel, need to fix them with some cable ties for example it fits perfect in the case and 1x140mm at rear. The air flow is fantastic it drop 5 degrees to my gpu temps 3070 stay 58-59 , GPU fans at 75%, and all other fans 1000 rpm you can always lower them if you don't like the noise which is not bad at all , my case before phanteks p600s was a great case as well but my GPU temps was 64-65 so definitely there is a difference I want to put my AIO on top because the case look too busy inside now it's a different story , I'm really happy with my purchase and the build quality aswell , it's on a heavy side with all the parts inside but I remove the hard drive cages inner door 2 metal covers inside and 1 behind the motherboard so it's fine , if you want future proof ,airflow ,and good quality this is the case for you .EDIT: just want to add for those who say that you can't fit 3x140mm fans on side you are wrong , as I show it on my picture 3x140mm noctua Fans are mounted on the side of 7000D you can't mount them with the screws but you can use cable ties and it fits perfect on the frame 3x140mm no vibrations at all .!

This is a hekkin' honker of a case, but damn is it a beaut! The cable management rails are a godsend and made the job of wiring everything that much easier. There are a few minor gripes regarding the difficulty of changing the front removable part (where the extra HDD bay can sit), and the lack of an additional milled out hole just above the motherboard to make things a bit easier, but overall I am happy with the case and the build quality.WARNING: This case is definitely on the heavier side and weighs around 15kg when it's just empty, so if you're not used to lifting awkwardly sized heavy objects, I strongly recommend you only move it with the help of another person.