DATA COMM Electronics 45-0231-WH USB Recessed Media Outlet Box, In-Wall Cable Management, Duplex Receptacle,4.0 Amp Dual USB Ports, Large Cable Pass-Through, Design for Thin Mounts & TV, White

What a great invention ...I purchased 4 of them one for each room where I have a TV.They are a very neat way to have your TV's on the wall without the ugly look of wires hanging down so if you're a neat freak this is a perfect solution!

Affords a tidy way to run and hold wires behind wall mounted TV

Very easy to install, only down fall is if you have 12/2 wire it will not stab into the back of the outlets.

Works as advertised but there are some things of which to be mindful. First, if you have an older home with 2" x 3" instead of 2" x 4"s, this will not work unless you modify the panel, which will prove difficult considering the density of the plastic or you will need free access to the back. In my case, my laundry room/heating room is behind the wall on which my TV is mounted so it didn't matter so much. Make sure to mount your television first before cutting the hole for the unit. I cut the hole first and tried to screw the mount over it which did not fit. This would've meant modifying the mount which of course when hanging a 25lb TV costing $700 not all that smart. Also, make double sure to know the locations of your beams. I have my TV mounted on a wall that has steel retaining beams in certain spots in the voids between the beams. I screwed this up a couple of times meaning I had to California patch the wall a bunch of times. I broke one of the screws that clamps the outlet to the wall meaning I had to rig up the last one. Lastly, instructions state to put it directly in the middle of the 16" space but it really should be off center a bit left or right because of the depth of the outlet. So if your beams are 16" on center, you should probably move it 2" off the 8" mark. You can use any square facing outlet receptacle. I had some extra tamper resistant outlets laying around. Worked great. You could probably use a GFCI as well. Just make sure to consult an electrician like I did if you have questions.

We decided to install a 55" LG TV on a main wall in our office and after much consideration, decided we wouldn't surface mount any wires or tracks in order to maintain a clean and professional look. Our challenge was that this fixture is ideally suited for either sheet rock walls or new construction - In our case the wall is made of concrete block - most of wish are filled with concrete. We also wanted to have a 2" electrical conduit pipe come into the back of the fixture. After all was said and done, we are very pleased with this fixture as we were able to cut the wall, install the conduit into the back of the fixture and close everything neatly. This fixture is very sturdy and well made - the self securing arms on the back side of the fixture held the fixture tightly in place while the concrete work was done to close up the whole thing. We chose to bore a 2" hole from the rear through the front inlet cowl of the fixture just to make access to the wires more direct - the cowl is a nice aesthetic touch but isn't necessary for us as the TV covers the fixture.entirely. I've purchased a number of similar Datacomm fixtures in the past and there have been no disappointments - They are all consistent in Excellent Quality, Styling and Function.I'd recommend that especially for concrete installs like ours, make all your electrical connections first and test them PRIOR to closing everything up with concrete. The outlet we got tested perfectly (see the circuit tester in the picture).Secondly, again with concrete, make sure you seal everything so as to prevent seepage of wet concrete into the fixture and especially it's outlet. Best to consult a licensed electrician for this. We used a chop saw to cut the conduit at a 45 degree angle and then glued the resulting pieces - once they set we wrapped it with duct tape to hold it firm and seal the joint.Some pics attached... Not quite done yet - more coming as we finish the project

Easy to install. The outlet that was included is only back stab and appears to be very cheaply made.

Bought it for one of those new fancy LED mirror medicine cabinets. It works fantastic. Easy to install and is hidden behind the medicine cabinet.

Easy to install just make sure you're in between the studs no mollies required what's nice about this product is you can stuff all your wires in the wall good product

We all know that Amazon lists more than it's share of junk, however this is not on that list. Very happy with the fit and finish and worked perfectly in my wall mount bracket, although I feel it's perhaps just a stroke of luck. I've attached pictures that show how little spare room I had to fit the box within the frame of the wall mount base. In fact, I had to run the right edge of the plate through my table saw as it was overlapping onto the bracket. You'll want to check the opening space on your bracket before you place the order. Good quality product.

Perfect! Just what I needed. My only comment is to make sure that your TV mount will fit after this installation. This product protrudes off of the wall by 2-3 mm, I had to modify my TV mount since it is flush to the wall.I am not explaining this properly. In essence, after installing this product, my TV mount did not fit anymore. I had to purchase 3 washers per bolt to slightly pull it off of the wall so that this would fit on top of the media plate. There was nothing wrong with the product, my comment is that you might need to modify your TV mount after installation of this product. In the end, all I needed were 12 washers from home depot and I was back in business.Hope this helps!

This was great. Install was easy. What’s not easy was running my wire to the light switch for power. I had like three studs to drill through but got it done in the end. I really light now you don’t need to screw anything into a stud. It just locks into the drywall. Pretty genius.

I really like this product but one of the four tabs that hold the fixture into the drywall was stripped right out of the box. The metal bracket that clamps the wall literally fell off as I was trying to install the fixture. It is obvious that the threaded part was deformed and would never have worked.I installed it anyway and installation is a breeze.

I have used a number of different versions of this product from different suppliers and was really impressed with this one. It comes with a template which makes cutting the wall much easier and gives an exact fit. It fits well and has a very tidy finish. It was delivered to my door in a couple of days which allowed me to focus on the project instead of doing supply runs. I'm really happy with the product and would buy again no question.