Armacost LightingPureVue Dimmable LED Undercabinet Puck Light, Daylight 5000K, Brushed Steel 253411

Very good quality, solid metal body and very bright. I install into cabinet display with remote control and it works great.

High quality lights. Trim ring is heavy aluminum, which makes a good heat sink to help the little LED chips last much longer. Nice finish, complete and easy to understand installation instructions too.

We waited for years to find the perfect led lights for under our cabinets. Finally we found this solution. They are great lights. Keep in mind that we've had them installed for only 2 days and at this point we are very happy. I'll write another review after a few months. Hope they remain good. We like them.

I bought 4 of the black 2700k puck lights and opted for a flush install. The way the flush mount works is there are 3 rigid metal clips that screw on the top of the unit to hold the light in place from the top of the cabinet. I cut the holes in my cabinet with a 2 1/8" inch hole saw and found that the metal flush mount clips were just too rigid to bend enough to allow the puck light to slide into the hole and to be installed from the inside of the cabinet. I thought maybe I could get it to go if I really pushed hard, punched it, or if I smacked it firmly with a rubber hammer, but I didn't because I figured the light would break or bend. But luckily I had access to the top of the cabinet so I slid the unit in with no clips at first and then screwed the clips from the top outside of the cabinet. That worked perfectly, nice and snug. If you can't get access to the top side of your cabinet to screw the clips in then I HIGHLY RECCOMEND YOU TEST FIT THE FLUSH MOUNT ON A SCRAP SURFACE BEFORE YOU DRILL YOUR CABINET just incase you can't get it to fit either. It would be a disaster to cut the 2 1/8" hole and then switch to the puck mount install method which would only need a very small hole to be drilled for the wire to slide through. As far as quality, not too bad! The flush mount looks really good in my glass door cabinets. At the lowest dimmer settings one of my units is very noticeably dimmer than the other 3 but then matches brightness once I get up to 20% or higher. Also, I'm powering these on the same power supply with an LED strip under the same cabinets. At the highest power settings the LED strip appears to over power the brightness of these puck lights but does balance better at mid power levels. Perhaps if you were pairing these with LED strips you should go with high intensity LED strips only if you need task lighting but then maybe stick with less intensity LED strips if you just need accent lighting, which is my setup. Looking forward to enjoying these!

I recently purchased 6 of the Armacost puck lights and two of their 20 watt transformers. I was tired of using cheaply made lower cost puck lights for my under the cabinet lighting. These are just what I was looking for.It happens that one of the transformers was missing a small piece which helps to hold the wires securely at their connection. I could have easily returned it to Amazon and got a replacement. Even easier though was that I emailed Armacost support at 3:36 pm requesting the missing part. The next morning at 11.37 am I got a reply with the UPS tracking number telling me a new transformer was being shipped to my house. Two days later, I had the transformer! If that's not SUPERB customer service than I don't know what is!This gives me great confidence in this company.Installation was a little harder than I thought because you have to solder or, in some other way use connectors, to connect the lights in parallel. I used the solder method because I thought that would be the most secure. The part that makes this a little hard is that I chose to solder the wires with the pucks installed under the cabinet in order to know where to cut the wires to join them. That meant soldering more than a foot above the counter. It worked out great though!

The media could not be loaded.  I purchased the Armacost PureVue 233412 Dimmable LED Puck, the 810100 10 Watt Standard Power Supply and the 523420 LED Wireless Remote Controller. Very happy with the entire setup! Low cost and easy installation!

I have a custom built desk unit with overhead cabinets in my office that I installed a 5 light LED puck set. One of the lights started to flicker and I couldn't stop it. I bought this so I wouldn't have to spend for a whole new set. It is 12 V, like the old set, and I checked that it worked before I did anything, which it did. I was able to splice the wires into the connector from the bad light, plug it into the terminal. The light is a little bit brighter than the old one, but it is in the corner of the unit behind my monitor, so it doesn't matter that much. The warm color is a good match to the old lights and not noticeably different. Much cheaper than a new light set.

I bot the lights and the driver from Armacost. I love the way they look...but they get very hot.I cannot hold my palm on them past count of 5. The inside bottom of the cabinet gets very warm. I replaced the first driver with another one suggested by Armacost. No difference. Already had to replace 4-5 of the lights. I am hoping Armacost can resolve this. If not - I guess you just have to replace them every 3 years.