KHCCC 90 Degree Corner Clamp - Right Angle - Corner & T-Joint Clamps for Woodworking - Carpentry Tools & Accessories - Holiday Home Improvement Gifts for Him

Fast delivery. Correct product. Good condition. Kreg makes great products, what else can you say.

The clamp doesn't have all the grip of any face clamp or else, but it works fine for the main use, butt joints at right angles. The main purpose is to hold the pieces together in order to use screws or pocket hole joints, that works as designed. Do not expect gorilla pressure on the clamp, it is not intended for that, only to keep the pieces at 90 degrees and use pocket holes, screws and nails. I wish to have one of this on my first cabinet I used a corner clamp since the main intention is to hold everything in order to put the screws. The adjustment screw is easy to use.

The tool works great but I needed to make 2 adjustments to get it there as shown in the pictures. The first is that it had almost zero clamping pressure. I read somewhere how to fix this and it seemed to work. You need to back out the adjustment screw most of the way, cycle the tool, and then adjust it to the pressure you need. Kreg should do this at the factory so shame on them for delivering these in this condition. The 2nd adjustment was that the boards were noticeably out of square (1 to 2 degrees which amplifies over the cabinet distances of course as 1 deg = .017"/1"). I checked the jaws for flatness and squareness and saw that one jaw was slightly out of flat in the direction that was consistent with what I observed in the clamped boards. I took a file and carefully flattened the offending jaw and now they are quite square and repeatable. The clamp is now very handy to use and accurate. The disappointing thing is that Kreg could have produced the tool this way so it is not up to their normal quality standards and they should fix this before losing the public on a well conceived and useful tool

Great product works as advertised!

I got the Kreg KHCCC corner clamp for some woodworking projects, and it does the job but there are a few things that could be better. The automatic adjustment feature is nice and makes it easy to set up but I found it a bit tricky to get the perfect hold every time. Sometimes it’s a little too tight or not tight enough which can throw off your project. The build quality is solid, though, and once you get it adjusted right it holds corners and joints securely. It works well for cabinets and boxes but it’s not the most user-friendly tool if you're not experienced. Overall, it’s good for the price but it could be a little more precise and easier to use. It’s decent but I’m not completely sold on it.

I purchased 2 of these clamps. Neither one will hold 3/4 inch plywood when assembling a cabinet. I have a right angle clamp by Kreg that uses the same auto adjust that works like a charm. I may have been lucky enough to get 2 defective clamps. So I contacted Kreg about this. The same day I received a reply describing how to reset the clamps and it this doesn't work to let them know. So I followed the instructions and the clamps begin to work like they should. I have to commend Kreg on their quick response. Here is how to reset the auto adjust clamps. " So you will open the jaws and back out that adjustment screw to the point where it is really loose but not falling out. You should see around 3/8" of threads between the bottom of the head of the screw to where it screws into the mechanism. Then you will close the jaws then open them back up. After that, you can bring that adjustment screw back to the positive around halfway down and try to clamp it down. That adjustment is not an exact adjustment, you may have to tighten it more or loosen it more to get the correct pressure you want to apply. When you are using the clamp, you will want to make sure you are opening the clamp fully when you are moving the clamp. This will allow the Automaxx system to reset to zero each time. You should only need to adjust the adjustment screw if you need to add or take out pressure from the clamp as the clamp will adjust to different thicknesses on its own. "

These are an imitation of the actual KREG product. I compared to an actual KREG at the store and these look somewhat less polished and less robust. They work okay, but have at least one serious FUNCTIONAL LIMITATION. The actual KREG product has an adjustable corner stop, but this cheap knock-off does not. If you watch the (KREG-made) video they pirated to advertise this known-off, you can see them use it. It's the beveled, spring loaded piece on the smaller / inside clamp face. On the KREG you can pull up on and rotate the stop to configure the joint. Say you have 'bottom' and 'side' pieces for your joint. If you have the corner stop turned one way, the the 'side' would run all the way to the stop / outside of the joint and the 'top' would but into it. Kinda like this: |_ If you rotate the corner stop the other way, 'bottom' will go all the way to the stop, which will be the outside of the finished joint, and the 'side' will butt into the 'top' piece. Not being able to easily change this is a severe limitation on the usefulness of the clamp. It CAN be changed by unscrewing the stop, rotating it, and screwing it back in. This is a pain in the anatomy because it's difficult to get at the screw and difficult to re-assemble. Not super hard, but not something you want to do every time you put the clamp in a different position. So, false advertising in calling it a KREG product and using the stolen video that highlights features these clamps don't actually have. Boo. I hadn't really shopped for these when I purchased them, so I didn't realize how much cheaper they were than the actual KREG product, or I would have known they were knock-offs. I doubt I'll send them back, but I wouldn't buy them with the hard-to change corner stop.

Très facile d'utilisation, je mets la note de 4 pour le prix. Cet outil reste qqmm très cher.

I have not been able to use the product at all as it jammed on me in the first 10 minutes of playing with it to see how it worked. I will be calling Kreg as soon as I get a working phone. Overall it seems like a great product and the auto adjust worked well for 10 minutes. I have a project coming up to use it on and can't wait till I get a replacement. Next year in 2022 when wood is available and prices come down I will be building a new kitchen and will really need this. Im sure it was just a fluke as my Kreg Jig 520 works great and has seen a little use already. Wish I had got one long ago. Update Oct 14 2021 I called Kreg and talked to a gentleman within 1 minute of calling. He was extremely helpful and knew how to resolve my issue. That took just one more minute. The package comes with an 800 number for help. I would highly recommend Kreg to everyone. Product is sturdy and tech support is FAST. I have a project to start using it in two days and I am very much looking forward to that

Good clamps

Es una buena pinza para el taller

Well engineered. I initially bought some corner clamps that to all intents and purposes looked like Kreg clamps but when they arrived they were a cheap and poorly engineered imitation. I sent them back and ordered the Kreg which are in a different league. Great product