ScubaproPremium Retractor with Snap

Secured a G2C dive computer to my BCD shoulder strap D-ring. Every time I checked depth/air/etc. it secured the G2C back into position and held it right in place. Quality!

I saw another reviewer (Robert M) who did a similar install - I wanted to offer mine:Up front: I started with the multi-mount ($22) accessory that is meant to go with the Hydros Pro (but I assume you could do something similar with whatever BC you have)1. ScubaPro Premium Retractor: I unscrewed the 4x screws that kept the overall housing together (be careful)1a. Take out the plastic "Stop Button", (I had no use for this feature) leaving you with perfectly aligned holes.2. I took out the bolt snap that came with it (this drastically reduces the overall size of the retractor)...immediately re-install the bolts to keep everything tight.3. I purchsed the same bolts (but longer) from Home Depot (Stainless)4. I hack-sawed about 1/8" from the purchased tipped screw (to keep the depth and prevent any sharp edges)5. I kept the plastic washer, and mounted the retractor, using the "created holes" from the vacant "stop button" and into the "multi-mount".--- --- ---6. I then unscrewed the existing 2x phillips head black screws from the other side, and replaced them with 2x eyelet screws (also from Home depot (stainless), same pattern...7. I fished a zip-tie through these 2x eyelets, arount the multi-mount, and secured everything.Permanent mount, streamlined, and clean!You may notice I replaced the split ring with a black solid ring...this is just my OCD, and not needed. By all means, have at it!I hope this helps!

This scubapro retractor is made of high quality components and uses a spring coil as the retractor mechanism. I modified mine to use on my scubapro hydros pro.... The metal hardware it came with were high quality as well. *NOTE* The orginal locking/unlocking slide button did get in the way and seemed to be more of a hassle for it would lock/unlock on it's own... so I just removed it.

I have purchased this to replace a retractor that broke after 3 dive trips. This is a much heavier and well built retractor.

Failed after less than 20 uses

The pro and con are the same there is a line lock, but the release is small

Very nice, as described

Generally I like this size and weight of this clip. Once you know where the lock is, it is relatively easy to lock and unlock to prevent or allow extension. It held the weight of my camera well. The issue is that twice the lock unlocked itself as I was coming out of the water, allowing the camera to drop and practically trip me. I may just need to be sure it was locked fully, thus my headline of "fussy".

Works perfectly!

Schön stabil und gute Qualität

Prima Ware, schnelle Lieferung

Habe den "SCUBAPRO Premium Retractor with Stop" als Halter für meine Tauchlampe gekauft.Die Lieferung ist sehr rasch erfolgt.Beim Auspacken macht der Retractor einen guten Eindruck. Er arretiert durch den "Stopp-Knopf" und lässt sich wieder leicht lösen. Die Länge des Kabels ist auch für Personen mit längeren Armen geeignet, und auch dann noch eine Kabelreserve vorhanden.Habe ihn in Süß- und Salzwasser benutzt, bei Tauchtiefen bis fast 40m. Es gab bei keiner Tiefe irgendwelche Funktionsstörungen. Lediglich nach ungefähr dem 11 Salzwassertauchgang, rollte sich das "Kabel" nicht mehr ganz auf. Es fehlt ungefähr 1cm der sich nicht mehr aufrollt.Fazit:+ Süß- und Salzwassertauglich+ Robust- nach mehrmaligen Gebrauch im Salzwasser rollt das Kabel sich nicht mehr ganz ein (steht ungefähr 1cm raus)

Dziala jak nalerzy . Problem jest gdy jest wyciągnięta linka i naciśnie się guzik zwalniający wtedy gdy się nie trzyma za koniec linki .linka sie bardzo szybko zwija i jest niebezpiecznie dla paluszków:-) .