105A Epoxy Resin (32 fl oz) Bundle with 206A Slow Epoxy Hardener (7 fl oz). Also Includes one Resin and one Hardener Pump.

Excellent product. Easy to use. Pot time at 60 - 65 degrees was 30+ minutes with working time near an hour. Mixed product has low viscosity and gells slowly. It adhears to surfaces better and runs less if you are patient and allow time to gell. I am using the product to bond a large wood project. The metering pumps are a must have and make mixing totally fool proof. West Systems has a great web site and lots of information on how to use. Also several You Tube videos on using the product. Product can be stored with the pumps in the original containers for an extended time so minimal clean up.

This is excellent resin. No odor. Great working time. Cures solid and tough but also sands easily. Highly recommend it.

Used to glue together a new gate made of cedar and will be exposed to the elements. Easy to use. Viscosity is somewhat thicker than Titebond but still very easy to spread with a disposable glue brush. Easy to sand away the drips. Open time was 20+ minutes using the slow setting hardener which was essential as this was a somewhat complicated glue-up. I love the pumps that measure the correct amount of each. I expect this will be my new primary glue for exterior work.

The best part is the pump system, so easy to use, No scale needed. This stuff dries like absolute glass, and cleans up with rubbing alcohol before drying of course. It runs into wherever you need it to being pretty thin. There is almost no smell at all. I used this in a confined space with minimal ventilation, no mask and had zero issue with smell as well as my family who were Present when I used it. I used this epoxy to wet out the carbon/Kevlar inlay and fill the tip in my rc boat hull. This is amazing stuff, I don’t think I’ll be using any other epoxy for structural projects. My first choice seems to be a fantastic one. Working time is perfect for what I did with it. Around a 90 minute work time on surfaces with a thin film or 35-45 minutes in the pot. Soooo worth it. If I make a mold/boat I’ll be using this stuff without a doubt.

I bought this for an outdoor furniture project. The mini pumps make mixing a breeze. It has a very low viscosity without fillers. I used it for sealing and laminating. Requires a filler to increase the viscosity for general bonding. Excellent adhesion and easy to clean up after curing. I used the 206 slow set hardener since my project required many joints. The pot life was about 20 minutes so I was able assemble 20 joints without panicing. Can be used for many applications depending on the type of filer.

Works well once cured. I wish it was less viscous for a longer time. My specific application required pushing through an applicator, which was challenging.

This was great. Pumps were great, good instructions. Used this to fill in some gap in a slab of cherry wood. Everything worked perfect. I sand down the unavoidable excess with a random orbital. It all worked well and was very easy with the pump measure system. Since it’s winter now make sure you bring your epoxy inside overnight so it gets up to a normal temp otherwise cloudiness could occur if you are going with a no tint clear. I used powdered charcoal off some old embers from the fireplace and separately mixed a batch with the wood powder left from sanding. Couldn’t have been more pleased. The packaging left things loose, that’s my only complaint.

Pumps make it easy to accurately measure resin and hardener for correct ratio. Pumps also make it easy to mix a small batch or larger, as needed, for the job. I bought the slow hardener on purpose so I'd have more working time. I'm filling cracks on a piece of exotic hardwood and it's pretty tedious work to fill, move along, check, go back to refill, pop air bubbles, etc. while the mixture remains workable. After mixing for about 2 minuets, I'm getting over 25 minutes working time in 60-65 degree temps before the mixture starts becoming too thick to use. Great product, recommend for filling cracks and voids in woodworking projects.