Sewell Ghost Wire Terminal Block, 14, 16, and 18 AWG, 4 Pack

I would not consider using GhostWire without these terminal blocks unless I was soldering my own solution.If you are not buying a pack of these with your GhostWire - and you don't have any skill in soldering/electronics, then you are making a mistake and you will not have a good experience.They are simple to use, four precision flathead screws hold the wire in place.Be sure to strip back a wee bit extra GhostWire and fold it over on itself (stick side in) so you get a slightly thicker contact surface for the screw to hold.Just watch some videos and read Sewell's own documentation on the product and you should have a great time.I see a lot of reviews complaining that this is bulky, and I don't really understand. Of course I planned my installation out ahead of time so that both terminations would be reasonably hidden, and I kept some of the non-sticky surface I stripped back to place back over the block to sort of hide it.In all I would say this is about as thick as your average modern smartphone at most, and no wider than the GhostWire you are pairing it with.

Since we were getting rid of the carpet and putting down a floating laminate floor in the family room it was time to hide the ugly speaker wire going from the receiver around the walls and to the rear speakers. The ghost wire was simple to tape down to the underlayment from the front of the room to the back and super flat so it doesn't interfere with the laminate floor planks.Since I already had the baseboards off I was able to cut a small slit the width of the ghost wire at the bottom of the drywall just above the base 2x4. From there I fed the ghost wire into the slit and used one of these terminal blocks to transition to regular speaker wire where I connected them to a nice looking wall plate I installed at the same height as the plugs in the room https://www.amazon.com/gp/product/B001TK89L2/ref=ppx_yo_dt_b_asin_title_o01_s01?ie=UTF8&psc=1.I did the same thing at the back of the room and now you can't see any speaker wire at all. Yay!

Needs re-engineering. Ghost cable works well and terminal blocks look like they will mate well. However, the connection is made with two tiny screws. Two (of three) speakers sounded great, but the third had a very weak signal. Unfortunately I had already patched and spackled the wall. I am removing the wire and starting over. Solution - redesign the block so the connector clamps to the cable. I am grinding down a single edged razor blade to make a surface to clamp the connector to the cable. A lot of work, but I want a permanent installation.Update: Don’t use razor blade, it breaks under pressure. The aluminum back works perfectly and can be cut to size with wire cutters. Cut off both ends and blade removes easily. Provides a secure connection to the ghost wire.Another suggestion... Don’t make turns unless you use electrical tape. I changed my wiring plan and went diagonal, making connections behind the speakers and behind the AV console, wiring is almost invisible.

Installation was a breeze and my rear speakers play extremely well.

Recently ran ghost wire and needed to terminate the ends. These are excellent! I wish I could have gotten the newer model in 4 conductor but it was not available.Everything went smoothly, no issues at all. My ONLY two complaints are: no way to fasten this to a wall. None. I cut some double sided tape and used that. Lastly as stated previously, I would have liked the newer, cleaner model.Other than that, these are excellent. Don’t hesitate or cheap out. You need them!

I'm struggling with my thoughts on this product. The wire itself is great, I ran it along the baseboard and even before painting it's almost invisible. But these terminal blocks are just ugly. They aren't adhesive, nor do they mount flush to the wall. So you end up with a flat wire, and then this ugly block hanging off the wall pulling the wire with it. While it works great in my use case (behind the couch), I can't help but think there must be a more elegant solution.

I have used Ghost Wire 2.0 and Sewell terminals in the remodel of my movie room, and now, you can't see (or trip on) any of the wires that go to the speakers anymore. Great system, but I wish the connectors were a bit more affordable.

Ghost wire, an excellent product, I purchased the 4 conductor ordered 25' and installed one piece under carpet. When terminating I found the terminals shipped were for only one channel!! Why buy 4 conductor when the termination block is for one channel. So I had to use the balance of the roll and came up 8" short bt improvised by installing terminal block then pulling it back under the carpet to terminate the other end! I see that this product has a terminal that has 4 holes for 2 channels but it is not available. Kinda crummy in my book. Sounds great though!!