I am using a TB6600 at 2 amps and 36 volts and get over 1,000 rpm but have to use an acceleration curve as the motor won't go from a dead stop to that rpm without stalling.

Nema 17 Stepper Motor Bipolar 2A 59Ncm(84oz.in) 48mm Body 4-lead 3D Printer/CNC

Nema 17 Stepper Motor Bipolar 2A 59Ncm(84oz.in) 48mm Body 4-lead 3D Printer/CNC

Q: What are the recomended volts and amps for max torque?

The torque in a stepper motor is proportional to the current. For the motor in question, the max current is shown as 2A. The winding resistance is given as 1.4 ohms per phase which works out the 2.8 Volts (2 amps x 1.4 ohms). However, this is not the end of the story. In order to achieve the 2 amp rating once the motor is in motion, requires a much higher supply voltage than 2.8 Volts. This is because once the motor moves, it generates a internal voltage that subtracts from the supply voltage. Additionally, the motor winding inductance prevents the current from rising immediately. To counteract these two forces, you need to apply a much higher voltage to the motor to force the current to the desired level. Using a modern stepper driver that provides adjustable current limiting makes this easy. The overdrive voltage needed will depend on the maximum voltage that the driver can handle, the insulation breakdown voltage of the stepper motor, and the desired speed you need reach. A good starting point is 10 X the value obtained by looking at the the winding resistance and maximum current ratings. In this case 2.8V (see above). That would imply that an overdrive voltage of 28V would be reasonable to use. If you chose this voltage, make sure the stepper driver can handle it. Also make sure your power supply can supply the current. You can back this value down as needed if you don't have to run a very high speeds. Hope this helps you out.

Q: Will this stepper motor work as a replacement for a soyo sy42sth47-1504a used in the lulzbot mini 3d printer?

Based on my review of the two sets of specs, my answer is, this motor will PROBABLY work as a replacement. The physical dimensions and the step angle are a match. This motor requires somewhat more current and has slightly more torque. Unless I missed an important detail, I believe that these motors will work.

Q: Is the 2A max/peak? What's an expected normal amperage?

2A is rated current, we recommend you drive this motor with rated current.

4.6/5

产品编号: 234208694

安全交易

细节

Brand
STEPPERONLINE
Voltage
12 Volts
Horsepower
1.4 hp
Product Dimensions
42W x 42H
Material
As shown in

📏Compact 48mm body

🔌2.0A rated current

⚙️59Ncm high torque

经常一起购买

STEPPERONLINE Nema 17 Stepper Motor Bipolar 2A 59Ncm(84oz.in) 48mm Body 4-Lead W/ 1m Cable and Connector Compatible with 3D Printer/CNC

HiLetgo 5pcs A4988 Stepstick Stepper Motor Driver Module with Heat Sink for 3D Printer Reprap Suitable for Mendel Huxley Arduino

ELEGOO 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Ribbon Cables Kit Compatible with Arduino Projects

描述

⚡ Power your precision projects with torque that won’t quit!

PLUG PLAY READY - Includes 1m cable with 0.1" pitch connector for quick setup
DURABLE LIGHTWEIGHT - Only 399g with a robust 5mm shaft for long-lasting reliability
EFFORTLESS INTEGRATION - Standard NEMA 17 size fits most 3D printers & CNC machines
UNMATCHED TORQUE POWER - 59Ncm (84oz.in) holding torque for precision control
RELIABLE CURRENT RATING - 2.0A rated current ensures consistent performance under load

The STEPPERONLINE NEMA 17 Bipolar Stepper Motor delivers a powerful 59Ncm holding torque with a compact 48mm body, optimized for 3D printers and CNC machines. Rated at 2.0A with a 1.4-ohm resistance, it ensures smooth, reliable motion control. Equipped with a 1m cable and standard 0.1" pitch connector, this lightweight 399g motor offers easy installation and durable performance for professional-grade precision.

规格

Brand	STEPPERONLINE
Voltage	12 Volts
Horsepower	1.4 hp
Product Dimensions	42W x 42H Millimeters
Material	As shown in the image
Item Weight	0.88 Pounds
Shaft Diameter	5 Millimetres
Manufacturer	STEPPERONLINE
UPC	191388825313 798167993654 191579035491 701056358779 190657686020 712322835252 789164236554 715624560631
Model number	17HS19-2004S
Colour	As shown in the image
Number of Memory Sticks	1
Item Weight	399 g
Item model number	17HS19-2004S
Power Source	corded electric
Included Components	1
Are batteries included?	No

有问题吗？看看别人问了什么

What are the recomended volts and amps for max torque?

Will this stepper motor work as a replacement for a soyo sy42sth47-1504a used in the lulzbot mini 3d printer?

what is the rpm?

Is the 2A max/peak? What's an expected normal amperage?

4.6

全部来自已验证的购买

R**N

Great

Nice Stepper motor it a small motor but working grealy.Only thing is the price, it is bit costly.

10.05.2024

常见问题

TrustPilot

TrustScore 4.5 | 7,300多个评论

Rajesh P.

当我对产品有疑问时，客户服务非常出色。

2天前

尤素夫·A.

总体来说，体验非常棒。会推荐给朋友和家人。

1 个月前

查看所有TrustPiLot评论

全球购物，通过 Desertcart 享受优惠

物有所值

各种产品的价格具有竞争力

全球购物

为 100 多个国家的数百万购物者提供服务

增强保护

深受全球购物者喜爱的值得信赖的支付方式

客户保证

深受全球购物者喜爱的值得信赖的支付方式。

沙漠车应用程序

随时随地随时随地购物。

HK$506

关税和税费包括

Hong Kong店铺

免运费

with PRO Membership

免费退货

30天对于 PRO 会员用户

15天无会员资格

安全交易

TrustPilot

TrustScore 4.5 | 7,300多个评论

苏雷什· K.

质量和快速送货让我印象深刻。会再次来这里购物。

4天前

哈立德 Z.

从订购到送货的体验都很棒。强烈推荐！

1 周前

查看所有TrustPiLot评论