MG Chemicals - 841AR-15ML Nickel Print (Conductive Paint), 0.7 Ounce (Pack of 1)

One day, I go to turn on my Novation Circuit and it's freaking out! She was making her own chaotic dubstep madness without my permission! That said, dubstep is not where I am at in life right now!!! I was saddened by this and my feeling was hurt. I looked for similar instances of possessed Novation Circuits online and found that I was not alone in my pain. There was only one thing to do... take it apart!Pulling the sulicone(rubber) pad off the bottom was a pain but not impossible. I peeled the pad back carefully as to not stretch it or tear it. Screws ahoy the rest of the teardown was simple. When I got inside the box it was pretty filthy. Dust is said to be the culprit in this specific malfunction and jeezus holy merry was it a grandmother's old jewelry box stuffed in the back of the closet, inside the Circuit box!Surprisingly there was no dust between the plastic contact layer and the copper touch circuits. All I had at the time of autopsy was acetone so I cleaned the copper contacts and then started wiping down the plastic contact sheet with the printed black conductive paint. DONT USE ACETONE ON THIS STEP!!! Stupid me, I started wiping off the black conductive paint almost immediately! I repeat... DONT USE ACETONE TO CLEAN ELECTRIC CONTACT PAINT!!! I was further saddened and my feeling was nearly crushed at this point! Did I give up hope and call my fun little beat box a wash? HELL NO!!! This just meant I got a little work to get done!The internet was hopeless on information on fixing pressure pad contacts for synths. I had to get creative! So I took to Amazon for assistance of course!!!Searching for electric contact paint led me to this product. As I use MG Chemicals for other DIY electronic projects I knew I could put my faith in their products and potentially bring my Novation Circuit back to a jam worthy state. It wasn't cheap for a can of paint but it was up the bizniss of what I thought I needed to do the thing I gotta do.After receiving the can a few days after hitting purchase, it took weeks too fester the bullocks to get on it... I did today...I did a test spray to compare resistance between the factory paint and the MG Chemicals paint. The MG was nearly if not more than double the resistance between distances but this was all I got and by golly gee whiz I was gonna do it anyways!!! Plus if it didn't work I still have a whole can of acetone by my side! So I cleared the rest of the factory contact paint with intention this time using acetone to give me a clean slate. Carefully masking off the area around the square pockets I prepped for spray pretty darn well and was proud of my work.I sprayed 2 good coats and a light finish coat pretty evenly. Not having a "clean room" sucks because dust loves fresh spray paint... all was not lost tho! Zona (another great item on Amazon) makes really fine sanding cloth. After a sufficient dry time(10-15 minutes(I have no patience for drying paint)) I started with 1200 grit and sanded the 3 particles of dust right down smooth and it hopefully evened out the pads to an even whatever... 2000 grit felt like a good grit to stop at as that's where my patience gave in and satisfaction settled. I then peeled back my masking job only for my pride to get bent a little too now. I reached again for ol' trusty acetone and made the best of what I could with the overspray that went under my proud masking job. It was sufficient enough at some point and the advice of an old Asian gentleman I once knew came into my head and said, "No Touchy Too Muchy!" Again with a settled satisfaction I moved on...I vacuumed everything twice and assembled the Circuit slowly and carefully knowing that this is when it usually goes wrong. Once again I dreamed of a dust free filtered clean room but who the hell has one of those in their shop!?! You just gotta do the best you can sometimes!Everything reassembled nicely and I even used a double stick tape to re-adhere the silicone bottomous. The time for redemption had come... my feeling was no longer hurt but was now anxious. I found a fitting plug and nodded to the powers that be...BEHOLD!!! She powered up better than before! At least I feel she did! Little Circuit's demon was exorcised! Her days of dubstep were long gone and her beats started making sense! She was off the Crack and back playing a groovy house beat like the good ol' days! Thank you MG Chemicals!!! You really did a service today saving the life of a groovy little beat box! ...not the best beat box I own but now I have a really deep personal and intimate relationship with the little Circuit and will always carry with me the fond memory of the day I saved my Novation Circuit thanks to MG Chemicals and their availability of some pretty unique products!Needless to say the sadness I had dulled long before I began working on this which really helped. I was not in a rush and the anxiety of losing my Circuit diminished. This became a case of learning from mistakes and bringing a new tool into my potential repertoire. I am happy all has worked out thus far and I can carry forth into my days knowing 1, when and where to use acetone B, MG Chemicals has my back and 3, It's not impossible... there is always a way!As for my feeling... rest be assured, it is safe as it should be...

Got for my Stratocaster. It was more than enough to do at least two guitars. It’s a little messy but it dries fast and got rid of almost all of my buzz. Definitely not acrylic based. But other than the smell, it did wonders for my guitar.

I was looking for something more conductive but this seems like a good product. I painted a strip on some paper and measured a resistance of about 2250 ohms per inch.It dried quickly and was pretty durable.

I’ve got a first year of production MIJ 1997 ESP Viper, which I love dearly. We recently moved and when I got back around to setting up my home studio again, I was getting a horrendous amount of buzz from my guitar. I mean, it was so bad that it was interfering with notes as they sustained out. No amount of repositioning myself in relation to my desk, monitor, ANYTHING, helped.After double checking all of the guitar wiring and grounds, unplugging everything in the room one by one, unplugging my router, etc.; I still wanted to yank my hair out.Now, if you know ESP, then you know that they’re some fine craftsman. Again, this is an ESP handmade in the Japanese facility back in the 90s. It’s not an LTD. Not that there’s anything wrong with LTD. It’s just apples and oranges. But, there was zero shielding anywhere in the guitar, except for some foil tape on the backside of the control cavity cover.I ordered this out of desperation really. My Hail Mary. It’s a small 12ml bottle, but there was enough for me to do 3 thick coats in all 3 cavities = the 2 pickup cavities and the control cavity.When you mix it, use something like a popsicle stick. If there’s any clumps, smash them with the stick until they break up. Stir well.Wipe the areas that you’ll paint with some alcohol. I did scuff the cavities with some sandpaper as best as I could beforehand, then used some compressed air to blow them out. Then the alcohol. Then mixed the paint again.Paint color is like a charcoal silver. I thought that I would prefer black, but I actually like the charcoal color because it’s easier to see if you missed any spots IMHO.Everything cleans up easily with a wet rag.Dry time between coats is around 15 minutes or so, depending on how thick your coats are. I didn’t rush it. Over the course of a couple hours I took my time to paint coats until the bottle ran out. As mentioned, 3 thick coats in all cavities.Instructions state that it takes 24 hours to fully cure. After about 5-6 hours, everything was plenty dry for me to put my pickups and pots and wiring back in. Then restring and adjust everything. And of course I couldn’t wait. So…I was floored. 90% of the noise was gone. Not only that, but I could now actually reposition myself and get the electrical interference noise to go away 100%!But here’s the kicker. After the paint had fully cured after 24 hours or so? The guitar is now dead silent. No repositioning needed. It works!

Bought because it was sold as conductive paint, it did not conduct even a little bit for me. Was using it to repair broken defrost lines for car window. Put a few coats on and it has zero continuity even when checking within an inch length on one line. Would not recommend for anything other than being black paint. Maybe I misunderstood something but to me conductive means it conducts electricity.